分享
ASTM_D_3285_-_93_2005.pdf
下载文档

ID:179156

大小:73.21KB

页数:3页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_3285_ _93_2005
Designation:D 3285 93(Reapproved 2005)An Amrican National StandardStandard Test Method forWater Absorptiveness of Nonbibulous Paper andPaperboard(Cobb Test)1This standard is issued under the fixed designation D 3285;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the quan-tity of water absorbed in a specified time by nonbibulous paperand paperboard with a minimum thickness of 0.1 mm.This testmethod is generally applicable to sized paper and paperboard,but is not recommended as a sizing test for writing papers.Thetest method is based upon studies by Cobb and Loew,Cobb,and other investigators(1,2,3,4).21.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3D 585 Practice for Sampling and Accepting a Single Lot ofPaper,Paperboard,Fiberboard,and Related ProductD 685 Practice for Conditioning Paper and Paper Productsfor TestingD 824 Test Method for Rate of Absorption of Water byBibulous Papers3.Significance and Use3.1 Water absorptiveness is a function of various character-istics of paper or board,including sizing,porosity,and fibercomposition.3.2 This test method is useful in comparing various sheetsor nonbibulous(not highly absorbent)paper or paperboard asto the relative rate of penetration of aqueous solutions,such asadhesives or coatings.It will indicate to some degree thesurface and internal sizing.This test method is not intended asa water-resistance test,nor to measure the resistance to minutequantities of a liquid,such as from a writing pen.4.Apparatus4.1 Water Absorption Apparatus,to permit one side of thespecimen to be wetted uniformly at the moment the soakingperiod begins,and to allow controlled rapid removal of thewater from the specimen at the end of the test period.Thespecimen holder as shown in Fig.1 comprises a metal ring witha machined lower face,11.28 6 0.02-cm inside diameter(corresponding to a cross-sectional area of 100 cm2),2.5 cmhigh and about 0.6 cm thick,clamped to a flat base plate about15 by 15 cm with a metal cross bar 17 by 2.5 by 0.6 cm and twowing nuts on a pair of studs.The cross bar has a hole at one endand a slot at the other to facilitate assembly and use.On thebase plate is a rubber mat,larger than the outside dimensionsof the ring,on which the specimen is clamped.NOTE1The metal parts should preferably be of brass or othercorrosion-resistant material.NOTE2Several versions of the water absorption apparatus are nowavailable.Although the basic procedure for performing the test is notchanged,the clamping mechanism is.This may affect the time required toremove the specimen from the apparatus.4.2 Metal Roller,solid brass having a smooth face 20 cmwide and weighing 10.0 6 0.5 kg.4.3 Timer,stopwatch or electric timer reading in seconds.4.4 Graduated Cylinder,100 mL.4.5 Balance,with an accuracy of 0.01 g,or better.5.Reagents and Materials5.1 Water,distilled or deionized.5.2 Blotting Paper,a quantity of sheets of standard blottingpaper,200 mm2(8 in.2),weighing 250 6 10 g/m2oven-dry,0.495 to 0.521 mm(0.0195 to 0.0205 in.)thick,and having arate of absorbency of 25 s or less when tested with 1.0 mL ofwater in accordance with Test Method D 824.The blotter musthave a capillary rise of 50 to 100 mm of water(mean of MDand CM)when measured by the Klemm Test(see annex).1This test method is under the jurisdiction of ASTM Committee D06 on Paperand Paper Products and is the direct responsibility of Subcommittee D06.92 on TestMethods.Current edition approved June 1,2005.Published August 2005.Originallyapproved in 1973.Last previous edition approved in 1999 as D 3285 93(1999).2The boldface numbers in parentheses refer to the list of references at the end ofthis test method.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.6.Test Specimens6.1 Obtain a sample of the paper in accordance withPractice D 585.From each test unit,cut specimens to a sizeslightly greater than the outside dimensions of the ring of theapparatus(that is,squares 125 by 125 mm).The test piecesshould be free of folds,wrinkles,or other blemishes notcommonly inherent in the paper.For hard-sized papers(ab-sorbing less than 100 g of water/m2)use 10 specimens per testunit.For soft-sized p

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开