ASTM_D_3712_-_18.pdf

Designation:D371218Designation:369/(95)Standard Test Method ofAnalysis of Oil-Soluble Sulfonates by LiquidChromatography1This standard is issued under the fixed designation D3712;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the analysis of refined and crudenatural and synthetic oil-soluble sulfonate products.Resins,ifpresent,are recovered with the oil phase and carboxylates arerecovered as sulfonates.1.2 This test method covers the determination of mineraloil,sodium sulfonate,inorganic salts,water,basicity or acidity,average molecular weight,and relative density of sodiumsulfonate products.1.3 This test method covers the determination of mineraloil,sulfonate,water,base number,average molecular weight,and relative density of calcium,barium,magnesium,andammonium sulfonate products.1.4 The values stated in SI units are to be regarded asstandard.The values given in parentheses after SI units areprovided for information only and are not considered standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D95 Test Method for Water in Petroleum Products andBituminous Materials by DistillationD2896 Test Method for Base Number of Petroleum Productsby Potentiometric Perchloric Acid Titration3.Terminology3.1 Symbols:3.1.1 Following are definitions of the symbols used inSection 17,and as noted in the sections in parentheses.A=grams of sample of calcium,barium,magnesium,or ammoniumsulfonate(8.1.1).B=volume of chloroform solution,mL(10.1).C=grams of sample of sodium sulfonate(10.1.1).D=grams of oil recovered(10.4).E=grams of sodium sulfonate recovered(10.5).F=grams of residue from chloroform blank(10.6).G=grams of residue from alcohol blank(10.6).H=grams of sodium sulfonate(11.1).I=grams of sodium sulfate ash from sodium sulfonate(11.2).J=T/KS.K=valence of cation.S=average equivalent weight of sodium sulfonate(17.1.4).T=average molecular weight of calcium,barium,magnesium,orammonium sulfonate(17.1.5).U=percentage of sodium sulfonate(17.1.2).V=percentage of calcium,barium,magnesium,or ammoniumsulfonate(17.1.3).Wc=grams of water contained in pycnometer at 25 C(6.9).Ws=grams of sample contained in pycnometer at 25 C(15.1).X=grams of sodium sulfonate sample for basicity(12.1).Y=volume of standard H2SO4or NaOH solution used to determinebasicity or acidity(12.1).Z=normality of standard H2SO4or NaOH solution to determine freebasicity or acidity(12.1).AA=grams of sodium sulfonate product ashed(13.1).BB=grams of sodium sulfate from inorganic salt determination(13.1).1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricantsand is the direct responsibility ofSubcommittee D02.04.0C on Liquid Chromatography.Current edition approved April 1,2018.Published May 2018.Originallyapproved in 1978.Last previous edition approved in 2017 as D3712 05(2017).DOI:10.1520/D3712-18.This test method was adopted as a joint ASTM-IP standard.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 CCA=percentage of free acidity of sodium sulfonate product as H2SO4(17.1.6).CCB=percentage of free basicity of sodium sulfonate product as NaOH(17.1.6).DD=percentage of inorganic salts as sodium sulfate(17.1.7).4.Summary of Test Method4.1 The sample,except a sodium sulfonate product,isdissolved in ethyl ether and converted to sulfonic acid,usingdilute hydrochloric acid.The sulfonic acid after extraction isconverted to sodium sulfonate and the isolated sodium sul-fonate and mi