ASTM_D_3067_-_72_1991e1_scan.pdf

IND-STD ASTM D3067-72R78 VALID NOTICE I,68 m 9999998 0002877 3-ACCEPTANCE NOTICE ASTM D 3067-72R78 NOTICE 1 27 May I988 TITLE OF DOCUMENT:Standard Recommended Practice for Reporting Laboratory Results When Checking Aerosol Containers DATE OF SPECIFIC ISSUE ADOPTED:4 December 1972 RELEASING INDUSTRY GROUP:ASTM Acceptance Notice ASTM D 3067-72R78,dated 10 December 1980,has been reviewed and determined to be valid for use in acquisition.Custodians:Military Coordinating Activity:.Army-EA Navy-SH Air Force-68 Army-EA 1 I Review activities:Army-MD DLA-GS User activity:Army-GL.(AMSC N/A FSC 6810 DISTRIBUTION STATEMENT A.Approved for public release;distribution is unlimited.THIS DOCUMENT CONTAINS 1 i.y PAGES.-NOTICE:This standard has either been superseded and replaced by a new version or discontinued.Contact ASTM International(www.astm.org)for the latest information.ASTM D30bixEl 72 E 0759530 0075747 0 m Designation:D 3067-72(Reapproved 1991)E1 AMERICAN SOCIETY FOR TESTlNG AND MATERIALS 1016 Race St Philadelphia.Pa 1 SlO3 Reprinted from ttw Annual Book of ASTM Standards.Copyright ASTM If not listed In the current combined Index,will appear In the next edfiloh Standard Practice for Reporting Laboratory Results When Checking Aerosol Containers This standard is issued under the fixed designation D 3067;the number immediately following the designation indicates the year of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon(t)indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense and for listing in the DOD Index of Specijcations and Slandards.tl Nwrtt-Footnote 2 was corrcctcd editorially in June I99 I,1.Scope I.1 This practice is intended to provide a comprehensive list of results that should be reported by commercial labora-tories that are properly equipped and qualified,when checking any aerosol or pressure package for a fixed charge.2 1.2 This standard does not purport to address all of the safety problems,if any,associated with its use.It is the responsibility of the user of this standard to establish appro-priate saJety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents 2.1 ASTM Standards:r This practice is under the jurisdiction of ASTM Committee D-IO on Packaging and is the direct responsibility of Subcommittee D10.32 on Consumer Packages.Originally developed by the Chemical Specialties Manufacturers Associ-ation Current edition approved Dec.4,1972.Published January 1973.2 See CSMA Vendors lo the Trade,Chemical Specialties Manufacturers Assn.,1913 Eye St.NW,Washington,DC 20006.D 3063 Test Method for Pressure in Glass Aerosol Bottle.9 D3065 Test Methods for Flammability of Aerosol Products3 D 3066 Practice for Labeling Aerosol Packages3 D 3068 Specification for Safe Fill of Aerosol Containers3 D 3074 Test Methods for Pressure in Metal Aerosol Containers3 3.Reporting Results 3.1 The laboratory should report the results on the product specimens submitted in accordance with the fol-lowing ASTM standards:3.1.1 Labeling-Correct caution labeling and type of shipping label required,Practice D 3066.3.1.2 Flammability-Complete test and results,Test Method D 3065 and Department of Transportation Regula-tions.3.1.3 Fill-Specification D 3068.3.1.4 Pressure-Pressure(gage)at 70 and 130F(21 and WC),Test Methods D 3063 and D 3074.Annual Book of ASTM Standards,Vol 15.09.The American Society for Testing and Materials takes no position respecting the vatidky of any patent rights asserted in connection with any kern mentioned in thfs standard.Users of this standard are express/y advlsed that determination of the validity of any such patent rfghts,and the risk of infringement of such rights,are enttrely their own responsibffity.This standard Is subfern to revision et any t/me by the responsible technical committee and must be reviewed every ftve years and If nof revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.Your comments will receive careful consideration at a meeting of the responsible technical committee,which you may attend.ff you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards,1916 Race St.,Philadelphia,PA 19103.1