ASTM_D_3035_-_21.pdf

Designation:D303521An American National StandardStandard Specification forPolyethylene(PE)Plastic Pipe(DR-PR)Based on ControlledOutside Diameter1This standard is issued under the fixed designation D3035;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers polyethylene(PE)pipe madein thermoplastic pipe dimension ratios based on outside diam-eter IPS12to 3,for both non-pressure and pressure rated water(see Appendix X1).Included are requirements for polyethylenecompounds and PE plastic pipe,a system of nomenclature forPE plastic pipe,and requirements and test methods formaterials,workmanship,dimensions,sustained pressure,andburst pressure.Methods of marking are also given.NOTE1Significant changes have been made to this specification toremedy duplication of sizes with other specifications,for DIPS sizes andlarger sizes refer to the appropriate standard specification such asSpecification F714 or AWWA C906.1.2 For pipes produced under this specification that areintended for use in the distribution and transmission of potablewater without oxidizing disinfectants,potable and non-potablewater,grey water,reclaimed water,wastewater,force main andgravity municipal sewage,etc,the user should consult themanufacturer to determine whether the fluid being transportedis compatible with polyethylene pipe and will not affect theservice life beyond limits acceptable to the user.1.3 For pipes produced under this specification that areintended for use in the distribution and transmission of potablewater or other fluids containing oxidizing disinfectants(forexample,Hypochlorous acid or chloramines),special require-ments for PE compounds are specified in 5.2 and 5.3,and DRlimitations are specified in 6.2.1.1 and 6.2.2.1.NOTE2Refer to specification AWWA C901 for other suitable potablewater options.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The following safety hazards caveat pertains only to thetest methods portion,Section 7,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1238 Test Method for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD1598 Test Method for Time-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2290 Test Method for Apparent Hoop Tensile Strength ofPlastic or Reinforced Plastic PipeD2837 Test Method for Obtaining Hydrostatic Design Basisfor Thermoplastic Pipe Materials or Pressure Design Basisfor Thermoplastic Pipe ProductsD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsF412 Terminology Relating to Plastic Piping Systems1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.26 on OlefinBased Pipe.Current edition approved Aug.1,2021.Published August 2021.Originallyapproved in 1972.Last previous edition approved in 2015 as D3035 15.DOI:10.1520/D3035-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1F714 Specification for Polyethylene(PE)Plastic Pipe(DR-PR)Based on Outside Diamet