ASTM_D_4115_-_14.pdf

Designation:D411514Standard Performance Specification forWomens and Girls Knitted and Woven Dress GloveFabrics1This standard is issued under the fixed designation D4115;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This performance specification covers woven and knit-ted fabrics comprised of any textile fiber or mixture of fibers tobe used in womens and girls dress gloves.1.2 This performance specification is not applicable tofabrics used for interlinings and industrial-protective clothing.1.3 These requirements apply to the length and widthdirections for those properties where each fabric direction ispertinent.1.4 The following precautinary statement pertains only tothe test methods portion,Section 7,of this performancespecification.This standard does not purport to address all ofthe safety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD434 Test Method for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard Seam(Withdrawn2003)3D1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum(Elmendorf-Type)ApparatusD2261 Test Method for Tearing Strength of Fabrics by theTongue(Single Rip)Procedure(Constant-Rate-of-Extension Tensile Testing Machine)D2262 Test Method for Tearing Strength of Woven Fabricsby the Tongue(Single Rip)Method(Constant-Rate-of-Traverse Tensile Testing Machine)(Withdrawn 1995)3D2724 Test Methods for Bonded,Fused,and LaminatedApparel FabricsD3786 Test Method for Bursting Strength of TextileFabricsDiaphragm Bursting Strength Tester MethodD3787 Test Method for Bursting Strength of TextilesConstant-Rate-of-Traverse(CRT)Ball Burst TestD5034 Test Method for Breaking Strength and Elongation ofTextile Fabrics(Grab Test)D7022 Terminology Relating to Apparel2.2 AATCC Test Methods:48 Colorfastness to Crocking:Crockmeter Method16.3 Colorfastness to Light:Xenon-Arc23 Colorfastness to Burnt Gas Fumes61 Colorfastness to Laundering,Commercial:Accelerated116 Colorfastness to Crocking:Rotary Vertical CrockmeterMethod132 Colorfastness to Drycleaning135 Dimensional Changes of Fabrics after Home Launder-ing172 Colorfastness to Powdered Non-chlorine Bleach inHome Laundering188 Colorfastness to Sodium Hypochlorite Bleach in HomeLaunderingEvaluation Procedure No.1 Gray Scale for Color ChangeEvaluation Procedure No.2 Gray Scale for StainingEvaluation Procedure No.8 AATCC 9-Step ChromaticTransference Scale.A Glossary of AATCC Standard Terminology2.3 Federal Standard:516 CFR 1610 Standard for Flammability of Clothing Tex-tiles1This performance specification is under the jurisdiction of ASTM CommitteeD13 on Textiles and is the direct responsibility of Subcommittee D13.61 onApparel.Current edition approved Feb.1,2014.Published March 2014.Originallyapproved in 1982.Last previous edition approved in 2008 as D4115 02(2008).DOI:10.1520/D4115-14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Association of Textile Chemists and Colorists(AATCC),P.O.Box 12215,Research Triangle Park,NC 27709,http:/www.aatcc.org.5Available from Superintendent of Documents,Government Printing Office,Washington,DC 20402.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 16 CFR,Chapter IIConsumer Product Safety CommissionSubchapter DFlammable Fabrics Act Regulations2.4 Military Standard:6MIL-STD-105D Sampling Procedures and Tables for In-spection by AttributesNOTE1Reference to test methods in this standard give only thepermanent part of the designation of ASTM,AATCC,or other testmethods.The currrent edition of each test method cited shall prevail.3.Terminology3.1 For all terminology related to Apparel,see TerminologyD7022.3.1.1 The following terms are relevant to this standard:dress glove.3.2 For definitions of all other textile terms see TerminologyD123.3.3 For terms relating to chemical or colorfastness testing,refer to specific AATCC test methods,or the glossary ofAATCC Standard Terminology,or both.3.4 Definitions found in a dictionary of common terms aresuitable for terms used in this performance specification.4.Specification Requirements4.1 The properties of knitted and woven fabrics for wom-ens and girls dress gloves shall conform to the specificationrequirements in Table