ASTM_D_4114_-_21.pdf

Designation:D411421Standard Performance Specification forWoven Flat Lining Fabrics for Womens and Girls Apparel1This standard is issued under the fixed designation D4114;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This performance specification covers woven flat fabricscomprised of any textile fiber or mixture of fibers to be used aslinings for womens and girls apparel.1.2 This performance specification is not applicable towoven pile,woven fusible,fire-bonded fusible,sliver-knit pile,and sheepskin lining fabrics.1.3 These requirements apply to the length and widthdirections for those properties where fabric direction is perti-nent.1.4 The following precautionary statement pertains only tothe test methods portion,Section 7,of this performancespecification.This standard does not purport to address all ofthe safety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD434 Test Method for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard Seam(Withdrawn2003)3D1336 Test Method for Distortion of Yarn in Woven FabricsD1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum(Elmendorf-Type)ApparatusD2261 Test Method for Tearing Strength of Fabrics by theTongue(Single Rip)Procedure(Constant-Rate-of-Extension Tensile Testing Machine)D2724 Test Method for Bond Strength of Bonded,Fused,and Laminated Apparel FabricsD5034 Test Method for Breaking Strength and Elongation ofTextile Fabrics(Grab Test)D7022 Terminology Relating to Apparel2.2 AATCC Test Methods:4TM8 Colorfastness to Crocking:Crockmeter MethodTM15 Colorfastness to PerspirationTM16.3 Colorfastness to Light:Xenon-ArcTM23 Colorfastness to Burnt Gas FumesTM61 Colorfastness to Laundering:AcceleratedTM116 Colorfastness to Crocking:Rotary Vertical Crock-meter MethodTM124 Smoothness Appearance of Fabrics After RepeatedHome LaunderingTM132 Colorfastness to DrycleaningTM 135 Dimensional Changes of Fabrics after Home Laun-deringTM 172 Colorfastness to Powdered Non-Chlorine Bleach inHome LaunderingTM 188 Colorfastness to Sodium Hypochlorite Bleach inHome LaunderingEP No.1 Gray Scale for Color ChangeEP No.2 Gray Scale for StainingEP No.8 AATCC 9-Step Chromatic Transference ScaleM11 A Glossary of AATCC Standard Terminology1This performance specification is under the jurisdiction of ASTM CommitteeD13 on Textiles and is the direct responsibility of Subcommittee D13.61 onApparel.Current edition approved Jan.1,2021.Published January 2021.Originallyapproved in 1982.Last previous edition approved in 2014 as D4114 14.DOI:10.1520/D4114-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Association of Textile Chemists and Colorists(AATCC),P.O.Box 12215,Research Triangle Park,NC 27709,http:/www.aatcc.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.2.3 Federal Standard:516 CFR 1610 Chapter IIConsumer Product Safety Com-mission Subchapter DFlammable Fabrics Act Regula-tions2.4 Military Standard:6MIL-STD-105D Sampling Procedures and Tables for In-spection by AttributesNOTE1Reference to test methods in this performance specificationgive only the permanent part of the designation of ASTM,AATCC,orother test methods.The current editions of each test method cited shallprevail.3.Terminology3.1 Definitions:3.1.1 For terminology related to apparel see TerminologyD7022.3.1.2 For definitions of textile terms used in this perfor-mance specification,refer to the individualASTM andAATCCmethods and to Terminology D123.3.2 Definitions found in a dictionary of common terms aresuitable for this p