分享
ASTM_D_5213_-_12.pdf
下载文档

ID:177727

大小:94.62KB

页数:6页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_5213_ _12
Designation:D521312Standard Specification forPolymeric Resin Film for Electrical Insulation and DielectricApplications1This standard is issued under the fixed designation D5213;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers requirements for the material,dimensions and tolerances,and property values of film,in sheetor strip form,with or without heat-sealable coatings.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.NOTE1This document is similar to IEC 60674,Part 3,Sheets 2,4,5,6,and 7.2.Referenced Documents2.1 ASTM Standards:2D149 Test Method for Dielectric Breakdown Voltage andDielectric Strength of Solid Electrical Insulating Materialsat Commercial Power FrequenciesD883 Terminology Relating to PlasticsD1711 Terminology Relating to Electrical InsulationD2305 Test Methods for Polymeric Films Used for Electri-cal InsulationD3636 Practice for Sampling and Judging Quality of SolidElectrical Insulating MaterialsD4088 Practice for Preparation for Shipment of Solid Elec-trical Insulating Materials(Withdrawn 2003)32.2 IEC Standards:Publication 60674-3 Specification for Electrical Films forElectrical Purposes43.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nologies D1711 and D883 unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.2.1 sheet,nmaterial greater than 75 mm in width.3.2.2 strip,nmaterial 75 mm or less in width.4.Classification4.1 This specification covers the following:4.1.1 Type IGeneral purpose,4.1.2 Type IIHeat sealable,4.1.2.1 Grade 1One side coated,and4.1.2.2 Grade 2Two sides coated.4.2 Materials:4.2.1 ItemAPoly(N,N-p,p-oxydiphenylenepyromellitimide),4.2.2 ItemBPoly(N,N-p,p-oxydiphenylenebiphenyltetracarboxylimide,4.2.3 ItemCPoly(N,N-p-phenylenebiphenyltetracarboxylimide),4.2.4 Item DFEP-fluorocarbon,and4.2.5 Item EPolyethylene terephthalate.4.2.6 Item FPolyethylene naphthalate.4.2.7 Item GPolyetherimide.5.Ordering Information5.1 Order the film covered by this specification stating thetype,grade,class,thickness,width,and roll dimensions.6.Materials6.1 Type I material is flexible,unsupported film.6.2 Type II material is film meeting all of the requirementsof Type I,and having a heat-sealable coating on one or bothsides.7.Requirements7.1 The film covered by this specification shall meet theproperty requirements given in Tables 1-7 and Table 8 whentested by the methods given in Test Methods D2305.1This specification is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is the direct responsibility ofSubcommittee D09.07 on Flexible and Rigid Insulating Materials.Current edition approved Nov.1,2012.Published November 2012.Orginallyapproved in 1991.Last previous edition approved in 2007 as D5213 07.DOI:10.1520/D5213-12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 TABLE 1 Property Values for Type I,Class A Film poly(N,N-p-p-oxydiphenylene pyromellitimide)Average Property ValueNominal Thickness,m(mils)7.5(0.3)13(0.5)20(0.8)25(1.0)50(2.0)75(3.0)100(4.0)130(5.0)Tensile strength,min MPa(psi),machine direction and transversedirection69(10 000)97(14 000)138(20 000)138(20 000)138(20 000)138(20 000)138(20 000)138(20 000)Elongation,min percent,machineand transverse direction1020353540454545Shrinkage,max percent,afterexposure to 200 C(392 F),machine and transverse direction.0.300.300.350.350.350.35Moisture absorption,max percent,100%RH4.04.04.04.04.04.04.04.0Dielectric strength,min kV/mm(V/mil),60 HzA,B120(3000)120(3000)180(4500)180(4500)150(3800)140(3600)100(2500)100(2500)Volume resistivity,min-cm,B,C10151015101510151015101510151015Permittivity,max at 1 kHzB4.04.04.04.04.04.04.04.0Dissipation factor,max at 1 kHzB0.0070.0050.0050.0040.0040.0040.0040.004AUse Type 3 electrodes in air of Table 1 of Test Method D149(opposing 6.4-mm diameter rods).BAt 23 C(73.4 F),50%RH.CThe median value of 5 measurements shall be used for compliance.TABLE 2 Property Values for Type I,Class B Film poly(N,N-p-p-oxydiphenylene biphenyltetracarboxylimid

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开