分享
ASTM_D_5387_-_93_2019.pdf
下载文档

ID:177453

大小:91.28KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_5387_ _93_2019
Designation:D538793(Reapproved 2019)Standard Guide forElements of a Complete Data Set for Non-CohesiveSediments1This standard is issued under the fixed designation D5387;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide covers criteria for a complete sediment dataset.1.2 This guide provides guidelines for the collection ofnon-cohesive sediment alluvial data.1.3 This guide describes what parameters should be mea-sured and stored to obtain a complete sediment and hydraulicdata set that could be used to compute sediment transport usingany prominently known sediment-transport equations.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1129 Terminology Relating to WaterD4410 Terminology for Fluvial SedimentD4411 Guide for Sampling Fluvial Sediment in MotionD4822 Guide for Selection of Methods of Particle SizeAnalysis of Fluvial Sediments(Manual Methods)D4823 Guide for Core Sampling Submerged,Unconsoli-dated Sediments3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this standard,refer toTerminologies D1129 and D4410.3.2 Definitions of Terms Specific to This Standard:3.2.1 diameter,intermediate axis,nthe diameter of asediment particle determined by direct measurement of the axisnormal to a plane containing the longest and shortest axes.3.2.2 diameter,nominal,nthe diameter of a sphere of thesame volume as the given particle(1).33.2.3 diameter,sieve,nthe size of sieve opening throughwhich a given particle of sediment will just pass.3.2.4 Dx,nthe diameter of the sediment particle that has xpercent of the sample less than this size(diameter is deter-mined by method of analysis;that is,sedimentation,size,nominal,etc.).3.2.4.1 DiscussionExample:D45is the diameter that has45%of the particles that have diameters finer than thespecified diameter.The percent may be by mass,volume,ornumbers and is determined from a particle size distributionanalysis.4.Summary of Guide4.1 This guide establishes criteria for a complete sedimentdata set and provides guidelines for the collection of data aboutnon-cohesive sediments.5.Significance and Use5.1 This guide describes what parameters should be mea-sured and stored to obtain a complete sediment and hydraulicdata set that could be used to compute sediment transport usingany prominently known sediment-transport equations.5.2 The criteria will address only the collection of data onnoncohesive sediment.A noncohesive sediment is one thatconsists of discrete particles and whose movement depends on1This guide is under the jurisdiction of ASTM Committee D19 on Water and isthe direct responsibility of Subcommittee D19.07 on Sediments,Geomorphology,and Open-Channel Flow.Current edition approved Nov.1,2019.Published January 2020.Originallyapproved in 1993.Last previous edition approved in 2013 as D5387 93(2013).DOI:10.1520/D5387-93R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The boldface numbers in parentheses refer to a list of references at the end ofthis standard.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.the particular properties of the particles themselves(1).Theseproperties can include particle size,shape,density,and positionon the streambed with respect to other particles.Generally,sand,gravel,cobbles,and boulders are considered to benoncohesive sediments.6.Procedure6.1 Parameters discussed here are divided into three majorcategories:sediment,hydraulic,and others.Within each ofthese categories there is a listing of the minimum param

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开