ASTM_D_473_-_22.pdf

Designation:D47322Manual of Petroleum Measurement Standards(MPMS),Chapter 10.1Standard Test Method forSediment in Crude Oils and Fuel Oils by the ExtractionMethod1This standard is issued under the fixed designation D473;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers the determination of sedimentin crude oils and fuel oils by extraction with toluene.Theprecision applies to a range of sediment levels from 0.01%to0.40%mass,although higher levels may be determined.NOTE1Precision on recycled oils and crankcase oils is unknown andadditional testing is required to determine that precision.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific warning statements,see 6.1.1.6 and 7.1.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4057 Practice for Manual Sampling of Petroleum andPetroleum Products(API MPMS Chapter 8.1)D4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD4177 Practice for Automatic Sampling of Petroleum andPetroleum Products(API MPMS Chapter 8.2)D5854 Practice for Mixing and Handling of Liquid Samplesof Petroleum and Petroleum Products(API MPMS Chap-ter 8.3)E29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications2.2 API Standards:3Chapter 1 Terms and Definitions DatabaseChapter 8.1 Manual Sampling of Petroleum and PetroleumProducts(ASTM Practice D4057)Chapter 8.2 Automatic Sampling of Petroleum and Petro-leum Products(ASTM Practice D4177)Chapter 8.3 Mixing and Handling of Liquid Samples ofPetroleum and Petroleum Products(ASTM PracticeD5854)2.3 ISO Standard:45272 Toluene for industrial useSpecifications3.Terminology3.1 For definitions of terms used in this standard testmethod,refer to Terminology D4175 and the API MPMSChapter 1 Terms and Definitions Database.4.Summary of Test Method4.1 Extract test portion of a representative oil sample,contained in a refractory thimble,with hot toluene until theresidue reaches constant mass.The mass of residue,calculatedas a percentage,is reported as sediment by extraction.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and the API Committee onPetroleum Measurement,and is the direct responsibility of Subcommittee D02.02/COMQ,the joint ASTM-API Committee on Hydrocarbon Measurement forCustody Transfer(Joint ASTM-API).This test method has been approved by thesponsoring committees and accepted by the Cooperating Societies in accordancewith established procedures.Current edition approved July 1,2022.Published July 2022.Originally approvedin 1938.Last previous edition approved in 2017 as D473 07(2017)1.DOI:10.1520/D0473-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Petroleum Institute(API),1220 L.St.,NW,Washington,DC 20005-4070,http:/api-ec.api.org.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standard Jointly copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,USA and the American Petroleum Institute(API),1220 L Street NW,Washington DC 20005,USAThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.15.Significance and Use5.1 A knowledge of the sediment content of crude oils andfuel oils is important both to the operation of refining and thebuying or selling of these commodities.6.Apparatus6.1 Usual laboratory apparatus and glassware,together withthe following ar