ASTM_D_5147_-_D_5147M_-_14.pdf

Designation:D5147/D5147M14Standard Test Methods forSampling and Testing Modified Bituminous Sheet Material1This standard is issued under the fixed designation D5147/D5147M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover procedures for sampling andtesting prefabricated,reinforced,polymer-modified bituminoussheet materials designed for single-or multiple-ply applicationin roofing and waterproofing membranes.These products mayuse various surfacing materials on one side.1.2 These test methods cover a number of different prod-ucts.Not all tests are required for every product.Only thosecalled out in the Product Standard are required.1.3 These test methods appear in the following order:SectionSampling4Conditioning5Thickness6Load Strain Properties7Tear Strength8Moisture Content9Water Absorption10Dimensional Stability11Low-Temperature Flexibility12Heat Conditioning13Accelerated Weathering14Granule Embedment15Compound Stability16Coating Thickness17Low Temperature Unrolling18Precision and Bias191.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D95 Test Method for Water in Petroleum Products andBituminous Materials by DistillationD146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing andWaterproofingD1204 Test Method for Linear Dimensional Changes ofNonrigid Thermoplastic Sheeting or Film at ElevatedTemperatureD4073 Test Method for Tensile-Tear Strength of BituminousRoofing MembranesD4798 Practice for Accelerated Weathering Test Conditionsand Procedures for Bituminous Materials(Xenon-ArcMethod)D4977 Test Method for Granule Adhesion to Mineral Sur-faced Roofing by AbrasionD5636 Test Method for Low Temperature Unrolling of Feltor Sheet Roofing and Waterproofing MaterialsD5869 Practice for Dark Oven Heat Exposure of Roofingand Waterproofing MaterialsD6162 Specification for Styrene Butadiene Styrene(SBS)Modified Bituminous Sheet Materials Using a Combina-tion of Polyester and Glass Fiber ReinforcementsD6163 Specification for Styrene Butadiene Styrene(SBS)Modified Bituminous Sheet Materials Using Glass FiberReinforcementsD6164 Specification for Styrene Butadiene Styrene(SBS)Modified Bituminous Sheet Materials Using PolyesterReinforcementsD6222 Specification forAtactic Polypropylene(APP)Modi-fied Bituminous Sheet Materials Using Polyester Rein-forcementsD6223 Specification forAtactic Polypropylene(APP)Modi-fied Bituminous Sheet Materials Using a Combination ofPolyester and Glass Fiber ReinforcementsD6298 Specification for Fiberglass Reinforced Styrene-Butadiene-Styrene(SBS)Modified Bituminous Sheetswith a Factory Applied Metal Surface1These test methods are under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and are the direct responsibility of SubcommitteeD08.04 on Felts,Fabrics and Bituminous Sheet Materials.Current edition approved Jan.1,2014.Published January 2014.Originallyapproved in 1991.Last previous edition approved in 2011 as D5147/D5147M 11a.DOI:10.1520/D5147_D5147M-14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D6509 Specification forAtactic Polypropylene(APP)Modi-fied Bituminous Base Sheet Materials Using Glass FiberReinforcementE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.Significance and Use3.1 These test methods are used for sampling and testingmodified bitumen sheet materials.Property requirements,de-termined by these test methods,are found in the followingproduct standards:Specifications D6162,D6163,D6164,D6222,D6223,D6298,and D6509.4.Sampling4.1 From each shipment or fraction thereof,select at randoma number of rolls equal to one half the cube root of the totalnumber of rolls in the lot.If the calculated number is fractional,express it as the next highest whole number.For conveni