ASTM_D_5498_-_12a.pdf

Designation:D549812aStandard Guide forDeveloping a Training Program for Personnel PerformingCoating and Lining Work Inspection for Nuclear Facilities1This standard is issued under the fixed designation D5498;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide is intended to assist those responsible fordeveloping a program for the indoctrination and training ofpersonnel performing coating and lining inspection work fornuclear facilities.1.2 It is recognized that organizations and job responsibili-ties vary widely among utilities and also among varioussupport and service companies.It is the responsibility of theuser of this guide to identify the appropriate subject matter forits program and its specific needs.1.3 Users of this guide must ensure that coating and liningwork complies not only with this guide,but also with thelicensees plant-specific quality assurance program and licens-ing commitments.2.Referenced Documents2.1 ASTM Standards:2D16 Terminology for Paint,Related Coatings,Materials,andApplicationsD610 Practice for Evaluating Degree of Rusting on PaintedSteel SurfacesD714 Test Method for Evaluating Degree of Blistering ofPaintsD1005 Test Method for Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD2240 Test Method for Rubber PropertyDurometer Hard-nessD2583 Test Method for Indentation Hardness of Rigid Plas-tics by Means of a Barcol ImpressorD3276 Guide for Painting Inspectors(Metal Substrates)D3359 Test Methods for Measuring Adhesion by Tape TestD3363 Test Method for Film Hardness by Pencil TestD3843 Practice for Quality Assurance for Protective Coat-ings Applied to Nuclear FacilitiesD3925 Practice for Sampling Liquid Paints and RelatedPigmented CoatingsD4138 Practices for Measurement of Dry Film Thickness ofProtective Coating Systems by Destructive,Cross-Sectioning MeansD4212 Test Method for Viscosity by Dip-Type ViscosityCupsD4214 Test Methods for Evaluating the Degree of Chalkingof Exterior Paint FilmsD4258 Practice for Surface Cleaning Concrete for CoatingD4259 Practice for Abrading ConcreteD4260 Practice for Liquid and Gelled Acid Etching ofConcreteD4261 Practice for Surface Cleaning Concrete MasonryUnits for CoatingD4262 Test Method for pH of Chemically Cleaned or EtchedConcrete SurfacesD4263 Test Method for Indicating Moisture in Concrete bythe Plastic Sheet MethodD4285 Test Method for Indicating Oil or Water in Com-pressed AirD4414 Practice for Measurement of Wet Film Thickness byNotch GagesD4417 Test Methods for Field Measurement of SurfaceProfile of Blast Cleaned SteelD4537 Guide for Establishing Procedures to Qualify andCertify Personnel Performing Coating and Lining WorkInspection in Nuclear FacilitiesD4538 Terminology Relating to Protective Coating andLining Work for Power Generation FacilitiesD4541 Test Method for Pull-Off Strength of Coatings UsingPortable Adhesion TestersD4610 Guide for Determining the Presence of and Remov-ing Microbial(Fungal or Algal)Growth on Paint andRelated CoatingsD4752 Practice for Measuring MEK Resistance of EthylSilicate(Inorganic)Zinc-Rich Primers by Solvent RubD4787 Practice for Continuity Verification of Liquid orSheet Linings Applied to Concrete Substrates1This guide is under the jurisdiction of ASTM Committee D33 on ProtectiveCoating and Lining Work for Power Generation Facilities and is the directresponsibility of Subcommittee D33.04 on Quality Systems and Inspection.Current edition approved Nov.1,2012.Published February 2013.Originallyapproved in 1994.Last previous edition approved in 2012 as D5498 12.DOI:10.1520/D5498-12A.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D4940 Test Method for Conductimetric Analysis of WaterSoluble Ionic Contamination of Blasting AbrasivesD5144 Guide for Use of Protective Coating Standards inNuclear Power PlantsD5162 Practice for Discontinuity(Holiday)Testing of Non-conductive Protective Coating on Metallic SubstratesD5163 Guide for Establishing a Program for ConditionAssessment of Coating Service Level I Coating Systemsin Nuclear Power PlantsD5402 Practice for Assessing the Solvent Resistance ofOrganic Coatings Using Solvent RubsD6132 Test Method for Nondestructive Measurement of DryFilm Thickness of Applied Organic Coatings Using anUltrasonic GageD6237 Guide for Painting Inspectors(Concrete and Ma-sonry Substrates)D6386 Practice for Preparation of Zinc(Hot-Dip Galva-nized)Coated Iron and Steel Product and HardwareSurfaces for PaintingD6677 Test