ASTM_D_5751_-_99_2019.pdf

Designation:D575199(Reapproved 2019)Standard Specification forAdhesives Used for Laminate Joints in NonstructuralLumber Products1This standard is issued under the fixed designation D5751;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers performance levels for adhe-sives to be used in laminate joints in nonstructural lumberproducts.Such products include,but are not limited to,interiorand exterior mouldings,window and door components or parts,and bonded lumber panels.This specification is to be used toevaluate adhesives as well as the adhesive bonds innonstructural-glued-lumber products.NOTE1This specification supersedes the laminate-joint portion ofSpecification D3110.NOTE2See 3.2.1 and 3.2.2 for descriptions of a dry-use-nonstructuraladhesive and a wet-use-nonstructural adhesive.1.2 This specification applies to laminate-joint specimensmade under both laboratory and field conditions.See Section 4for limitations in using this specification to evaluate industri-ally manufactured laminate joint products.1.3 The following safety caveat applies only to the appara-tus and test methods portions,Sections 6,7,8,and 9 of thisspecification:This standard does not purport to address all ofthe safety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 The values stated in inch-pound units are to be regardedas standard.1.5 In this specification,laminate joint refers to both faceand edge joints.1.6 The following index is provided as a guide to the testmethods in this specification:SectionApparatus6Conditioning7Material and Preparation of Assemblies andSpecimens8Exposure Conditions and Treatments9Testing,Calculation,and Reporting10NOTE3The conditioning needed for various stages in the preparationof the specimens and for the exposure tests are given in Sections 7,8,and9.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D905 Test Method for Strength Properties of AdhesiveBonds in Shear by Compression LoadingD907 Terminology of AdhesivesD2555 Practice for Establishing Clear Wood Strength ValuesD3110 Specification for Adhesives Used in Laminate Jointsfor Nonstructural Glued Lumber Products(Withdrawn1996)3D4442 Test Methods for Direct Moisture Content Measure-ment of Wood and Wood-Based MaterialsD5266 Practice for Estimating the Percentage of WoodFailure in Adhesive Bonded JointsE4 Practices for Force Verification of Testing MachinesE6 Terminology Relating to Methods of Mechanical TestingE41 Terminology Relating to Conditioning(Withdrawn2019)3E177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.Terminology3.1 Definitions:Many terms in this specification are definedin Terminologies D907,E6,and E41.3.1.1 bond,nthe union of materials by adhesives.1This specification is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.30 on WoodAdhesives.Current edition approved Feb.1,2019.Published February 2019.Originallyapproved in 1995.Last previous edition approved in 2012 as D5751 99(2012).DOI:10.1520/D5751-99R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.1.2 laminate joint,nin wood bonding,a joint made bybonding layers of adherends face-to-face or edge-to-edge toform thicker or wider stock.3.1.3 edge joint,nin wood bonding,a type of laminatejoint made by bonding adherends edge-to-edge with graindirections parallel to form wider stock.3.1.4 face joint,nin wood bonding,a type of laminatejoint made by bonding adherends f