ASTM_D_5560_-_95_2018.pdf

Designation:D556095(Reapproved 2018)Standard Test Method forDetermination of Neutral Fatty Matter Contained in Fats andOils1This standard is issued under the fixed designation D5560;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers all degraded glycerides,sincethey are neutral fats.However,this procedure does not neces-sarily determine all the mono and diglycerides that may bepresent in the sample.This is due to the water solublecharacteristics of some mono and diglycerides.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D5553 Test Method for Determination of the UnsaponifiableNonvolatile Matter in Sulfated Oils3.Significance and Use3.1 This test method is intended for the determination of theneutral fatty matter contained in fats and oils by means of etherextraction.4.Apparatus and Reagents4.1 Erlenmeyer Flask,125 mL.4.2 Separatory Funnel.4.3 NaOH,0.5 N.4.4 Petroleum Ether.4.5 Phenolphthalein Indicator.4.6 Ethyl Alcohol,denatured.5.Procedure5.1 Weigh 5 g of sample into a 125-mL assay flask and add50 mL of alcohol.Warm and rotate,if necessary,to dissolve.Titrate with 0.5 N NaOH to end point using phenolphthaleinindicator.Cool,then add 1 mL excess 0.5 N NaOH and rotateflask.Extract three times with 50-mL portions of petroleumether and wash combined ether layers with water until freefrom alkali.Evaporate ether and dry to constant weight.6.Calculation6.1 Calculate the total neutral oily matter as follows:total neutral oily matter5weight of residue3100weight of sample(1)6.2 Determine the total neutral oily matter includingunsaponifiables,if any,as in Test Method D5553,and subtractto obtain neutral fatty matter.7.Precision and Bias7.1 This test method is adopted from the procedures of theAmerican Leather ChemistsAssociation where it has long beenin use and where it was approved for publication before theinclusion of precision and bias statements was mandated.Theoriginal interlaboratory test data are no longer available.Theuser is cautioned to verify by the use of reference materials,ifavailable,that the precision and bias(or reproducibility)of thistest method is adequate for the contemplated use.8.Keywords8.1 fats and oils;leather;neutral fatty matter1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.08 on Fats and Oils.This testmethod was developed in cooperation with the American Leather Chemists Assn.(Method H 53-1957).Current edition approved Sept.1,2018.Published October 2018.Originallyapproved in 1994.Last previous edition approved in 2011 as D5560 95(2011).DOI:10.1520/D5560-95R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of there