ASTM_D_5363_-_03_2008.pdf

Designation:D536303(Reapproved 2008)Standard Specification forAnaerobic Single-Component Adhesives(AN)1This standard is issued under the fixed designation D5363;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers single-component anaerobicadhesives suitable for locking,sealing,and retaining threadedor cylindrical assemblies.The adhesives are cured to a solidstate when confined between closely fitting active metalsurfaces.1.2 This specification is intended to be a means of classify-ing anaerobic adhesives.It is not intended for engineeringdesign purposes.1.3 This specification is intended to replace Military Speci-fications MIL-S-22473,MIL-S-46163,and MIL-R-46082.1.4 The values stated in SI units are to be regarded as thestandard.1.5 The following safety hazards caveat pertains only to thetest methods portion,Section 7,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2A109/A109M Specification for Steel,Strip,Carbon(0.25Maximum Percent),Cold-RolledB36/B36M Specification for Brass Plate,Sheet,Strip,AndRolled BarB209 Specification for Aluminum and Aluminum-AlloySheet and PlateB633 Specification for Electrodeposited Coatings of Zinc onIron and SteelD56 Test Method for Flash Point by Tag Closed Cup TesterD439 Specification for Automotive Gasoline(Withdrawn1990)3D445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids(and Calculation of Dynamic Viscos-ity)D770 Specification for Isopropyl AlcoholD907 Terminology of AdhesivesD1084 Test Methods for Viscosity of AdhesivesD1193 Specification for Reagent WaterD2693 Specification for Ethylene GlycolD3951 Practice for Commercial PackagingD4562 Test Method for Shear Strength of Adhesives UsingPin-and-Collar SpecimenD4800 Guide for Classifying and Specifying AdhesivesD5648 Test Method for Torque-Tension Relationship ofAdhesives Used on Threaded Fasteners(Lubricity)D5649 Test Method for Torque Strength of Adhesives Usedon Threaded FastenersD5657 Test Method for Fluid TightnessAbility ofAdhesivesUsed on Threaded FastenersE122 Practice for Calculating Sample Size to Estimate,WithSpecified Precision,the Average for a Characteristic of aLot or Process2.2 Military Standards:MIL-STD-105 Sampling Procedures and Tables for Inspec-tion by Attributes4MIL-STD-129 Marking for Shipment and Storage4MIL-STD-810 Environmental Test Methods and Engineer-ing Guides4MIL-STD-118 Commercial Packaging of Supplies andEquipment42.3 Federal Standards:FED-STD-313 Material Safety Data Sheets,Preparation andSubmission of41This specification is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.60 on AdhesiveMaterial Classification System.Current edition approved Oct.1,2008.Published October 2008.Originallyapproved in 1993.Last previous edition approved in 2003 as D5363 031.DOI:10.1520/D5363-03R08.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/www.dodssp.daps.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.4 Federal Specifications:FF-N-836 Nut:Square,Hexagon,Cap,Slotted,Castle,Knurled,Welding and Single Ball Seat4PPP-B-636 Box,Shipping,Fiberboard4QQ-P-416 Plating,Cadmium,Electrodeposited42.5 Military Specifications:MIL-R-46082 Retaining Compounds,Single-Component,Anaerobic4MIL-S-22473Sealing,Locking,Retaining Compounds;Single-Component4MIL-S-46163 Sealing,Lubricating,and Wicking Com-pounds:Thread-Locking,Anaerobic,Single-Component4MIL-T-5624 Turbine Fuel,Aviation,Grades JP-4 and JP-542.6 U.S.Department of Transportation(DOT):Code of Federal Regulations,Parts 100 to 199,Departmentof Transportation Rules and Regulations for the Transpor-tation of Explosives and Other Dangerous Articles52.7 Society of Automotive Engineers:SAE J311 Fluid for Passenger Care Type AutomaticTransmissions,Information Report6SAE J429 Mechanical and Material Requirements for Exter-nally Threaded Fasteners6SAE AMS 2629 Jet Reference Fuel63.Terminology3.1 Definition