分享
ASTM_D_5199_-_12_2019.pdf
下载文档

ID:175842

大小:87.42KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_5199_ _12_2019
Designation:D519912(Reapproved 2019)Standard Test Method forMeasuring the Nominal Thickness of Geosynthetics1This standard is issued under the fixed designation D5199;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the measurement of the nominalthickness of geosynthetics,except textured and some struc-tured geomembranes where the entire surface of the presserfoot cannot come into complete contact with the geosyntheticsurface.1.2 This test method does not provide thickness values forgeosynthetics under variable normal compressive stresses.Thistest method determines nominal thickness,not necessarilyminimum thickness.1.3 The values stated in SI units are to be regarded asstandard.The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776/D1776M Practice for Conditioning and Testing Tex-tilesD2905 Practice for Statements on Number of Specimens forTextiles(Withdrawn 2008)3D4354 Practice for Sampling of Geosynthetics and RolledErosion Control Products(RECPs)for TestingD4439 Terminology for GeosyntheticsD5994/D5994M Test Method for Measuring Core Thicknessof Textured GeomembranesE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.Terminology3.1 For definitions of other terms relating to geotextiles andgeomembranes used in this standard,refer to TerminologyD4439.For definition of other textile terms used in thisstandard,refer to Terminology D123.3.2 Definitions:3.2.1 pressure,nthe force or load per unit area.3.2.2 structured geomembrane,ngeomembrane consist-ing of a flat core and protrusions on one or both sides.3.2.3 thickness(1)the distance between one planar surfaceand its opposite parallel and planar surface;(2)in the textiles,the distance between the upper and lower surfaces of thematerial,measured under a specified pressure and time.4.Summary of Test Method4.1 The nominal thickness of geosynthetics is determinedby observing the distance between two parallel surfacesconfining the tested material while under a specified pressure,after 5 s.5.Significance and Use5.1 Thickness is one of the basic physical properties used tocontrol the quality of many geosynthetics.Thickness valuescan be required for calculation of some geosynthetics proper-ties such as permeability and tensile stress,among others.5.2 The thickness of some geosynthetics may vary consid-erably with the applied normal load.Specific pressures andsurfaces on which they are applied are indicated in this methodto ensure all results are comparable.5.3 This test method may be used for acceptance testing ofcommercial shipments of geosynthetics for which this methodis applicable(see 1.1).NOTE1The user should be aware that the compressibility of somematerials,their rebound characteristics,and other phenomenon will affect1This test method is under the jurisdiction of ASTM Committee D35 onGeosynthetics and is the direct responsibility of Subcommittee D35.03 on Perme-ability and Filtration.Current edition approved June 15,2019.Published June 2019.Originallyapproved in 1991.Last previous edition approved in 2012 as D5199 12.DOI:10.1520/D5199-12R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 the thickness of some geosynthetics,following the time when they arerolled up,shipped,and stored.6.Apparatus6.1 Thickness Testing InstrumentThe thickness gaugeshall have a base(or anvil)a

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开