ASTM_D_5106_-_22.pdf

Designation:D510622Standard Specification forSteel Slag Aggregates for Asphalt Paving Mixtures1This standard is issued under the fixed designation D5106;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers crushed steel slag coarse andfine aggregates suitable for use in asphalt paving mixtures.1.2 Steel slag coarse and fine aggregates are currently beingused entirely(Note 1)or combined with other mineralaggregates,such as those covered in Specification D692/D692M or D1073,to produce paving mixtures similar to thosedescribed in Specification D3515 or D4215.NOTE1When 100%of the coarse aggregate in an asphalt mixture issteel slag,the amount of steel slag fines in that mixture may be limited toprevent bulking.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.NOTE2Sieve size is identified by its standard designation in Speci-fication E11.The alternative designation given in parentheses is forinformation only and does not represent a different standard sieve size.1.4 The text of this specification references notes andfootnotes which provide explanatory material.These notes andfootnotes(excluding those in tables and figures)shall not beconsidered as requirements of the standard.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C88/C88M Test Method for Soundness of Aggregates byUse of Sodium Sulfate or Magnesium SulfateC117 Test Method for Materials Finer than 75-m(No.200)Sieve in Mineral Aggregates by WashingC125 Terminology Relating to Concrete and Concrete Ag-gregatesC131/C131M Test Method for Resistance to Degradation ofSmall-Size Coarse Aggregate by Abrasion and Impact inthe Los Angeles MachineC136/C136M Test Method for Sieve Analysis of Fine andCoarse AggregatesC142/C142M Test Method for Clay Lumps and FriableParticles in AggregatesD8 Terminology Relating to Materials for Roads and Pave-mentsD75/D75M Practice for Sampling AggregatesD448 Classification for Sizes of Aggregate for Road andBridge ConstructionD692/D692M Specification for Coarse Aggregate for As-phalt Paving MixturesD1073 Specification for Fine Aggregate for Asphalt PavingMixturesD3319 Practice for the Accelerated Polishing of AggregatesUsing the British WheelD3515 Specification for Hot-Mixed,Hot-Laid BituminousPaving Mixtures(Withdrawn 2009)3D3665 Practice for Random Sampling of Construction Ma-terialsD4215 Specification for Cold-Mixed,Cold-Laid AsphaltPaving MixturesD4318 Test Methods for Liquid Limit,Plastic Limit,andPlasticity Index of SoilsD4792/D4792M Test Method for Potential Expansion ofAggregates from Hydration ReactionsD4867/D4867M Test Method for Effect of Moisture onAsphalt Concrete Paving MixturesD5711 Test Method for Determining the Adherent Coatingon Coarse Aggregates(Withdrawn 2012)3D5821 Test Method for Determining the Percentage ofFractured Particles in Coarse AggregateE11 Specification for Woven Wire Test Sieve Cloth and TestSieves1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.50 onAggregate Specifications.Current edition approved July 1,2022.Published July 2022.Originally approvedin 1991.Last previous edition approved in 2015 as D5106 15.DOI:10.1520/D5106-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.12.2 Federal Registrar:4SW846 1311 EPA Test Method,Toxicity CharacteristicLeaching Procedure3.Terminology3.1 For definitions of terms used in this specification,referto Terminologies C125 and D8.4.Ordering Information4.1 Orders for the material under this specification shallinclude the following information:4.1.1 The name of material(steel slag coarse aggregateand/or steel slag fine aggregate).4.1.2