分享
ASTM_D_5600_-_22.pdf
下载文档

ID:175785

大小:84.62KB

页数:5页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_5600_ _22
Designation:D560022Standard Test Method forTrace Metals in Petroleum Coke by Inductively CoupledPlasma Atomic Emission Spectrometry(ICP-AES)1This standard is issued under the fixed designation D5600;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the analysis for commonlydetermined trace metals in test specimens of raw and calcinedpetroleum coke by inductively coupled plasma atomic emis-sion spectroscopy.1.2 Elements for which this test method is applicable arelisted in Table 1.Detection limits,sensitivity,and optimumranges of the metals will vary with the matrices and model ofspectrometer.1.3 This test method is applicable only to samples contain-ing less than one mass%ash.1.4 Elements present at concentrations above the upper limitof the working ranges can be determined with additional,appropriate dilutions.1.5 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D346 Practice for Collection and Preparation of CokeSamples for Laboratory AnalysisD1193 Specification for Reagent WaterD4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD6299 Practice for Applying Statistical Quality Assuranceand Control Charting Techniques to Evaluate AnalyticalMeasurement System PerformanceD7260 Practice for Optimization,Calibration,and Valida-tion of Inductively Coupled Plasma-Atomic EmissionSpectrometry(ICP-AES)for Elemental Analysis of Petro-leum Products and LubricantsE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this test method,referto Terminology D4175.3.2 Definitions of Terms Specific to This Standard:3.2.1 gross samplethe original,uncrushed,representativeportion taken from a shipment or lot of coke.4.Summary of Test Method4.1 A test sample of the petroleum coke is ashed at 700 C.The ash is fused with lithium borate.The melt is dissolved indilute hydrochloric acid(HCl),and the resultant solution isanalyzed by inductively coupled plasma atomic emissionspectrometry(ICP-AES)using simultaneous,or sequentialmultielemental determination of elements.The solution isintroduced to the ICP instrument by free aspiration or by anoptional peristaltic pump.The concentrations of the tracemetals are then calculated by comparing the emission intensi-ties from the sample with the emission intensities of thestandards used in calibration.5.Significance and Use5.1 The presence and concentration of various metallicelements in a petroleum coke are major factors in determiningthe suitability of the coke for various end uses.This testmethod provides a means of determining the concentrations ofthese metallic elements in a coke sample.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricantsand is the direct responsibility ofSubcommittee D02.03 on Elemental Analysis.Current edition approved Oct.1,2022.Published October 2022.Originallyapproved in 1994.Last previous edition approved in 2017 as D5600 17.DOI:10.1520/D5600-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.15.2 The test method provides a standard procedure for useby buyer and seller in the commercial transfer of petroleumcoke to determine whether the petroleum coke meets thespecifications of the purchasing party.6.Interferences6.1 SpectralFollow the instrument manufacturers

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开