分享
ASTM_D_5991_-_17.pdf
下载文档

ID:175373

大小:73.36KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_5991_ _17
Designation:D599117Standard Practice forSeparation and Identification of Poly(Vinyl Chloride)(PVC)Contamination in Poly(Ethylene Terephthalate)(PET)Flake1This standard is issued under the fixed designation D5991;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This practice covers four procedures for separation andqualitative identification of poly(vinyl chloride)(PVC)con-tamination in poly(ethylene terephthalate)(PET)flakes.NOTE1Although not presented as a quantitative method,procedurespresented in this practice may be used to provide quantitative results at thediscretion of the user.The user assumes the responsibility to verify thereproducibility of quantitative results.Data from an independent sourcesuggest a PVC detection level of 200 ppm(w/w)based on an originalsample weight of 454 g.1.2 Procedure A is based on different fluorescence of PVCand PET when these polymers are exposed to ultraviolet(UV)light.1.3 Procedure B is an oven test based upon the charring ofPVC when it is heated in air at 235C.1.4 Procedures C and D are dye tests based on differentialstaining of PVC and PET.NOTE2Other polymers(for example,PETG)also absorb the stain orbrightener.Such interferences will result in false positive identification ofPVC as the contaminant.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific hazards see Section 8.NOTE3There is no known ISO equivalent to this standard.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1600 Terminology forAbbreviated Terms Relating to Plas-ticsIEEE/ASTM SI-10 American National Standard for Use ofthe International System of Units(SI):The Modern MetricSystem3.Terminology3.1 The terminology used in this practice is in accordancewith Terminology D1600.Units and symbols are in accordancewith IEEE/ASTM SI-10.3.2 Definitions of Terms Specific to This Standard:3.2.1 light material,npaper,polymers such as polyethyl-ene and polypropylene,and other materials with densities lessthan 1.00 g/cm3.4.Summary of Practice4.1 For the Beilstein Test,chlorine-containing materialsheated in a flame in contact with a copper wire produce acharacteristic green flame.4.2 With Procedure A,a known amount of PET flakes isexposed to ultraviolet radiation.PET normally fluoresces witha blue or violet color.Flakes fluorescing with different colorsare removed,weighed,and identified as PVC if they burn witha bright green flame when heated on a copper wire.4.3 With Procedure B,PET flakes are heated in an ovenmaintained at 235 6 5C.After a minimum of 45 min,theflakes are visually examined with removal and subsequentweighing of black,charred pieces.Pieces are confirmed asPVC using the same flame test mentioned in 4.1.4.4 With Procedure C,PET flakes are soaked in a blueacetone dye solution that preferentially stains any PVC flakes.These flakes are visually identified and subsequently removed,and weighed.The identification of PVC flakes is confirmedwith the flame test.1This practice is under the jurisdiction ofASTM Committee D20 on Plastics andis the direct responsibility of Subcommittee D20.95 on Recycled Plastics.Current edition approved Dec.1,2017.Published January 2018.Originallyapproved in 1996.Last previous edition approved in 2015 as D5991-15.DOI:10.1520/D5991-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.5 With Procedure D,PET flakes are heated with anaqueous solution containing an optical brightener that alsopreferentially stains the PVC flakes.The flakes are sorted underUV light in a dark room with removal and subsequentweighing of

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开