ASTM_D_5616_-_04_2022.pdf

Designation:D561604(Reapproved 2022)Standard Specification forReclaimed Trichloroethylene1This standard is issued under the fixed designation D5616;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the grades of trichloroethyl-ene2typically needed in various industries for noncriticalapplications such as in metal cleaning formulations.It may beused as a reference document by purchasers or personsestablishing in-house trichloroethylene recovery programs.1.2 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D1064 Test Methods for Iron in Rosin Tall Oil Fatty Acidsand Other Related Products(Withdrawn 2002)4D2108 Test Method for Color of Halogenated OrganicSolvents and Their Admixtures(Platinum-Cobalt Scale)D2109 Test Methods for Nonvolatile Matter in HalogenatedOrganic Solvents and Their AdmixturesD2111 Test Methods for Specific Gravity and Density ofHalogenated Organic Solvents and Their AdmixturesD2942 Test Method for Total Acid Acceptance of Haloge-nated Organic Solvents(Nonreflux Methods)D2989 Test Method for Acidity-Alkalinity of HalogenatedOrganic Solvents and Their AdmixturesD3401 Test Methods for Water in Halogenated OrganicSolvents and Their AdmixturesD3741 Test Methods for Appearance of Admixtures Con-taining Halogenated Organic SolventsD6806 Practice for Analysis of Halogenated Organic Sol-vents and Their Admixtures by Gas Chromatography2.2 Code of Federal Regulations:529CFR1910.1200 DepartmentofLabor,OSHARegulations,Hazard Communication49 CFR Parts 100 to 199 Department of TransportationHazardous Materials Regulations3.Classification3.1 Type IGenerally recognized for use in precision ap-plications.3.2 Type IIUse for less-demanding precision applications.3.3 Type IIIMay not be suitable for all applications.4.Properties4.1 Type I reclaimed trichloroethylene shall meet the re-quirements of Table 1.4.2 Type II reclaimed trichloroethylene shall meet the re-quirements of Table 1.4.3 Type III reclaimed trichloroethylene shall meet therequirements of Table 1.5.Packaging5.1 Industrial or commercial quantities shall be packagedand labeled in accordance with DOT regulations as found in49 CFR Parts 100 to 199,in accordance with state and localregulations,and in accordance with OSHAregulations found in29 CFR 1919.1200.6.Keywords6.1 halogenatedsolvent;reclaimed;TCE;tri;trichloroethyleneTypes I,II,and III1This specification is under the jurisdiction of ASTM Committee D26 onHalogenated Organic Solvents and Fire Extinguishing Agents and is the directresponsibility of Subcommittee D26.02 on Vapor Degreasing.Current edition approved May 1,2022.Published May 2022.Originallyapproved in 1994.Last previous edition approved in 2016 as D5616-04(2016).DOI:10.1520/D5616-04R22.2Trichloroethylene:CAS No.79-01-6.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this historical standard is referenced onwww.astm.org.5Available from U.S.Government Publishing Office(GPO),732 N.Capitol St.,NW,Washington,DC 20401-0001,http:/www.gpo.gov.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.If you feel that your comments have