分享
ASTM_D_5648_-_01_2019.pdf
下载文档

ID:175040

大小:69.93KB

页数:2页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_5648_ _01_2019
Designation:D564801(Reapproved 2019)Standard Test Method forTorque-Tension Relationship of Adhesives Used onThreaded Fasteners(Lubricity)1This standard is issued under the fixed designation D5648;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the torque-tension relationship(lubricity)of adhesives used for lockingand sealing threaded fasteners.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D907 Terminology of Adhesives2.2 Society of Automotive Engineers Standards:SAE J174 Torque Tension Test Procedure for Steel ThreadedFasteners3SAE J429 Mechanical and Material Requirements for Exter-nally Threaded Fasteners32.3 Federal Specification:FF-N-836Nut:Square,Hexagon,Cap,Slotted,Castle,Knurled,Welding and Single Ball Seat43.Terminology3.1 DefinitionsMany of the terms in this test method aredefined in Terminology D907.4.Summary of Test Method4.1 This test method consists of applying adhesive to athreaded fastener and measuring the developed tension appliedto the fastener at specified torques.Alternatively,the torquerequired to reach specified levels of bolt tension may bemeasured.5.Significance and Use5.1 On some applications of threaded fasteners,it is desir-able to control either the amount of developed tension when aspecified range of torque has been applied or the torquerequired to develop a specified range of tension.This testmethod is used to determine the effect of using adhesives onthe torque-tension relationship of threaded fasteners.5.2 Accurate torque-tension relationships may be measuredonly by defining and controlling the many related test param-eters.6.Apparatus6.1 Tension-Measuring Device,capable of measuring theaxial tension induced in the bolt as it is tightened,having anaccuracy within 65%of the test load.6.2 Torque-Measuring Device,of suitable capacity havingan accuracy within 65%of a given torque reading.7.Test Specimens7.1 BoltsAs-received,phosphate-and-oil-treated,38-in.size,16 threads per inch,Unified National Coarse thread series1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.60 on AdhesiveMaterial Classification System.Current edition approved June 1,2019.Published June 2019.Originallyapproved in 1994.Last previous edition approved in 2014 as D5648 01(2014).DOI:10.1520/D5648-01R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Society of Automotive Engineers(SAE),400 CommonwealthDr.,Warrendale,PA 15096-0001,http:/www.sae.org.4Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1(38by 16 UNC),Grade 5 bolts in accordance with SAE J429,having a minimum length of 112in.(38.1 mm)with hexagonalhead.7.2 Steel NutsAs-received,Type II,Style 4,nominally2164in.(8.3 mm)thick,conforming to Fed.Spec.FF-N-836.NOTE1Other fastener sizes and substrates may be used uponagreement between the supplier and the user of adhesives.7.3 Hardened Washers,conforming to the dimensional,metallurgical,mechanical,and finish requirements given inTable 1 of SAE J174.8.Procedure8.1 Determine the torque-tension relationship on not lessthan five specimens as follows:8.1.1 For liquid adhesives,insert the bolt in the tension-measur

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开