分享
ASTM_D_5992_-_96_2018.pdf
下载文档

ID:175000

大小:869.69KB

页数:25页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_5992_ _96_2018
Designation:D599296(Reapproved 2018)Standard Guide forDynamic Testing of Vulcanized Rubber and Rubber-LikeMaterials Using Vibratory Methods1This standard is issued under the fixed designation D5992;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide covers dynamic testing of vulcanized rubberand rubber-like(both hereinafter termed“rubber”or“elasto-meric”)materials and products,leading from the definitions ofterms used,through the basic mathematics and symbols,to themeasurement of stiffness and damping,and finally through theuse of specimen geometry and flexing method,to the measure-ment of dynamic modulus.1.2 This guide describes a variety of vibratory methods fordetermining dynamic properties,presenting them as options,not as requirements.The methods involve free resonantvibration,and forced resonant and nonresonant vibration.Inthe latter two cases the input is assumed to be sinusoidal.1.3 While the methods are primarily for the measurement ofmodulus,a material property,they may in many cases beapplied to measurements of the properties of full-scale prod-ucts.1.4 The methods described are primarily useful over therange of temperatures from 70C to+200C(100F to+400F)and for frequencies from 0.01 to 100 Hz.Not allinstruments and methods will accommodate the entire ranges.1.5 When employed for the measurement of dynamicmodulus,the methods are intended for materials having com-plex moduli in the range from 100 to 100 000 kPa(15 to15 000 psi)and damping angles from 0 to 90.Not allinstruments and methods will accommodate the entire ranges.1.6 Both translational and rotational methods are described.To simplify generic descriptions,the terminology of translationis used.The subject matter applies equally to the rotationalmode,substituting“torque”and“angular deflection”for“force”and“displacement.”1.7 This guide is divided into sections,some of whichinclude:SectionTerminology and Symbols3Factors Influencing Dynamic Measurement7Test Methods and Specimens8Nonresonant Analysis Methods and Their Influence onResults9Report10Mechanical and Instrumentation Factors Influencing DynamicMeasurementAnnex A1Guide to Further ReadingAppendix X1Double-Shear SpecimensDerivation of Equations andDescriptions of SpecimensAppendix X2Torsion SpecimensDerivation of Equations andDescriptions of SpecimensAppendix X3Compression/Tension SpecimensDerivation of Equationsand Descriptions of SpecimensAppendix X4Free Resonant VibrationEquations for Log Decrement andStiffnessAppendix X5Obtaining Loss Factor and Elastic Stiffness fromTransmissibility CurvesAppendix X61.8 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.9 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.10 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D945 Test Methods for Rubber Properties in Compression orShear(Mechanical Oscillograph)D1566 Terminology Relating to Rubber1This guide is under the jurisdiction of ASTM Committee D11 on Rubber andRubber-like Materials and is the direct responsibility of Subcommittee D11.10 onPhysical Testing.Current edition approved Aug.1,2018.Published September 2018.Originallyapproved in 1996.Last previous edition approved in 2011 as D5992 96(2011).DOI:10.1520/D5992-96R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.2 ISO Document:3ISO 2856 ElastomersGeneral Requirements for DynamicTesting2.3 DIN Document:4DIN 53 513 Determination of viscoelastic properties ofelastomers on exposure to forced vibration at non-resonant frequencies3.Terminology3.1 Definitions:3.1.1 Definitions

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开