ASTM_D_5788_-_95_2017.pdf

Designation:D578895(Reapproved 2017)Standard Guide forSpiking Organics into Aqueous Samples1This standard is issued under the fixed designation D5788;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide covers the general technique of“spiking”aqueous samples with organic analytes or components.It isintended to be applicable to a broad range of organic materialsin aqueous media.Although the specific details and handlingprocedures required for all types of compounds are notdescribed,this general approach is given to serve as a guidelineto the analyst in accurately preparing spiked samples forsubsequent analysis or comparison.Guidance is also providedto aid the analyst in calculating recoveries and interpretingresults.It is the responsibility of the analyst to determinewhether the methods and materials cited here are compatiblewith the analytes of interest.1.2 The procedures in this guide are focused on“matrixspike”preparation,analysis,results,and interpretation.Theapplicability of these procedures to the preparation of calibra-tion standards,calibration check standards,laboratory controlstandards,reference materials,and other quality control mate-rials by spiking is incidental.A sample(the matrix)is fortified(spiked)with the analyte of interest for a variety of analyticaland quality control purposes.While the spiking of multiplesample test portions is discussed,the method of standardadditions is not covered.1.3 This guide is intended for use in conjunction with theindividual analytical test method that provides procedures foranalysis of the analyte or component of interest.The testmethod is used to determine an analyte or componentsbackground level and,again after spiking,its now elevatedlevel.Each test method typically provides procedures not onlyfor samples,but also for calibration standards or analyticalcontrol solutions,or both.These procedures includepreparation,handling,storage,preservation,and analysis tech-niques.These procedures are applicable by extension,using theanalysts judgement on a case-by-case basis,to spikingsolutions,and are not reiterated in this guide.See also PracticeE200 for preparation and storage information.1.4 These procedures apply only to analytes that are solublein water at the concentration of the spike plus any backgroundmaterial,or to analytes soluble in a solvent that is itselfwater-soluble.The system used in the later case must result ina homogeneous solution of analyte and sample.Meaningfulrecovery data cannot be obtained if an aqueous solution orhomogeneous suspension of the analyte of interest in thesample cannot be attained.1.5 Matrix spiking may be performed in the field or in thelaboratory,depending on which part of the analytical process isto be tested.Field spiking tests the recovery of the overallprocess,including preservation and shipping of the sample.Laboratory spiking tests the laboratory process only.Spiking ofsample extracts,concentrates,or dilutions will test only thatportion of the process subsequent to the addition of the spike.1.6 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1129 Terminology Relating to WaterD1193 Specification for Reagent WaterD3694 Practices for Preparation of Sample Containers andfor Preservation of Organic ConstituentsD3856 Guide for Management Systems in LaboratoriesEngaged in Analysis of Water1This guide is under the jurisdiction of ASTM Committee D19 on Water and isthe direct responsibility of Subcommittee D19.06 on Methods for Analysis forOrganic Substances in Water.Current edition approved Dec.15,2017.Published January 2018.Originallyapproved in 1995.Last previous edition approved in 2011 as D5788 95(2011).DOI:10.1520/D5788-95R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.Un