ASTM_D_5896_-_96_2019e1.pdf

Designation:D589696(Reapproved 2019)1Standard Test Method forCarbohydrate Distribution of Cellulosic Materials1This standard is issued under the fixed designation D5896;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTESection 8.1 was editorially updated in December 2019.1.Scope1.1 This test method covers the determination of the carbo-hydrate composition of cellulosic materials such as groundwood meal,chemically refined pulp,mechanical pulps,brownstocks,and plant exudates(gums)by ion chromatogra-phy.This test method is suitable for rapid,routine testing oflarge numbers of samples with high accuracy and precision.For a review of this technique,see Lee(1).21.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For hazard statement,see Section 8.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D1193 Specification for Reagent WaterD1695 Terminology of Cellulose and Cellulose Derivatives3.Terminology3.1 For standard terminology of cellulose and cellulosederivatives,see Terminology D1695.3.2 Abbreviations:3.2.1 ICion chromatography,3.2.2 SPEsolid phase extraction,3.2.3 PADpulsed amperometric detector,3.2.4 PEDpulsed electrochemical detector,3.2.5 mMmillimolar.4.Summary of Test Method4.1 IC analysis of cellulosics requires the following opera-tions:(1)sample preparation,(2)total hydrolysis,(3)dilution,(4)SPE,(5)ion chromatographic analysis,and(6)calibration/calculation.5.Significance and Use5.1 This test method requires total hydrolysis of carbohy-drate material to monosaccharides,and is thus applicable toany cellulosic or related material that undergoes substantialhydrolysis,including cellulose derivatives such as celluloseacetate.5.2 The carbohydrate composition of a cellulosic materialcan be expressed on the basis of the total initial sample,or onthe basis of the carbohydrate portion of the sample.The formerrequires quantitative handling and may require special knowl-edge of the other components present in order to establish theabsolute carbohydrate level or determine individual woodhemicelluloses such as galactoglucomannan,etc.Since thesolid portion of purified pulps is almost all carbohydrate(98+%),the latter basis is often used to express the carbo-hydrate distribution as a percent.5.3 If heated under alkaline conditions,isomeric sugars maybegin to appear in the chromatogram.The major impuritypresent in purified pulps is saccharinic acids.These acidiccomponents,and other anions such as sulfate,carbonate,andacetate are removed by a strong base anion exchange SPE,and1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.36 on Cellulose and Cellulose Derivatives.Current edition approved Dec.1,2019.Published December 2019.Originallyapproved in 1996.Last previous edition approved in 2012 as D5896 96(2012).DOI:10.1520/D5896-96R19E01.2The boldface numbers in parentheses refer to the list of references at the end ofthis test method.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.would need to be determined separately to get a more exactcarbohydrate distribution.6.Apparatus6.1 Blender.6.2 Screw Cap Culture Tubes,25 by 150 mm,outsidediameter.6.3 Refrigerator.6.4 Pressure Cooker.6.5 SPE Cartridges.6.6 Water Bath.6.7 Ion Chromatograph.6.8 Moisture Balance.6.9 Hot Plate.6.10 Pipets.TOTAL HYDROLYSIS7.Reagents and Materials7.1 Sulfuric Acid(72 6 0.1 weight%):To 1 volume ofwater,add slowly while stirrin