ASTM_D_601_-_87_1998.pdf

Designation:D 601 87(Reapproved 1998)Standard Specification forOiticica Oil(Permanently Liquid)1This standard is issued under the fixed designation D 601;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers oiticica oil that has beentreated to render it permanently liquid.2.Referenced Documents2.1 ASTM Standards:D 445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids(and the Calculation of DynamicViscosity)2D 555 Guide for Testing Drying Oils3D 1466 Test Method for Sampling Liquid Oils and FattyAcids Commonly Used in Paints,Varnishes,and RelatedMaterials3D 1475 Test Method for Density of Paint,Varnish,Lacquer,and Related Products4D 1544 Test Method for Color of Transparent Liquids(Gardner Color Scale)4D 1545 Test Method for Viscosity of Transparent Liquidsby Bubble Time Method3D 1639 Test Method for Acid Value of Organic CoatingMaterials3D 1955 Test Method for Gel Time of Drying Oils3D 1958 Test Method for Chloroform Insoluble Matter inOiticica Oil3D 1959 Test Method for Iodine Value of Drying Oils andFatty Acids3D 1963 Test Method for Specific Gravity of Drying Oils,Varnishes,Resins,and Related Materials at 25/25 C33.Properties3.1 Oiticica oil(permanently liquid)shall conform to therequirements in Table 1.4.Test Methods4.1 SamplingSampling shall be conducted in accordancewith Test Method D 1466.4.2 The properties enumerated in this specification shall bedetermined in accordance with the applicable ASTM testmethods listed in Table 1.The significance of these testmethods enumerated under properties in this specification isdiscussed in Methods D 555.5.Keywords5.1 drying oils;oiticica oilThe American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connectionwith any item mentioned in this standard.Users of this standard are expressly advised that determination of the validity of any suchpatent rights,and the risk of infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Headquarters.Your comments will receive careful consideration at a meeting of the responsibletechnical committee,which you may attend.If you feel that your comments have not received a fair hearing you should make yourviews known to the ASTM Committee on Standards,100 Barr Harbor Drive,West Conshohocken,PA 19428.1This specification is under the jurisdiction of ASTM Committee D-1 on Paintand Related Coatings,Materials,andApplications,and is the direct responsibility ofSubcommittee D 01.32 on Drying Oils.Current edition approved Oct.30,1987.Published December 1987.Originallypublished as D 601 41.Last previous edition D 601 55(1981)e1.2Annual Book of ASTM Standards,Vol 05.01.3Annual Book of ASTM Standards,Vol 06.03.4Annual Book of ASTM Standards,Vol 06.01.TABLE 1 Physical PropertiesPropertyRequirementASTM MethodSpecific gravity,25/25C,min0.972D 1963,D1475Viscosity at 25C,approximate11 to 23D 1545,D445StokesAcid value,max8.0D 1639Iodine value(Wijs),min135D 1959Color(Gardner 1933 Standards),max11D 1544Gel time,minutes,max17D 1955Refractive index at 25C,min1.5100.Matter insoluble in chloroform,max,%0.1D 19581AMERICAN SOCIETY FOR TESTING AND MATERIALS100 Barr Harbor Dr.,West Conshohocken,PA 19428Reprinted from the Annual Book of ASTM Standards.Copyright ASTM