分享
ASTM_D_6155_-_19.pdf
下载文档

ID:174411

大小:95.11KB

页数:3页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_6155_ _19
Designation:D615519Standard Specification forNontraditional Coarse Aggregates for Asphalt PavingMixtures1This standard is issued under the fixed designation D6155;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the use of coarse aggregatesnot traditionally used in asphalt paving mixtures.These non-traditional aggregates can be described as any aggregate otherthan those described in Specifications D692/D692M,D693,D1139/D1139M,andD5106(crushedstone,crushedhydraulic-cement concrete,crushed blast-furnace slag,steelfurnace slag,and crushed gravel)suitable for use in asphaltpaving mixtures,as described in Specification D3515 orD4215.1.2 The text of this specification references notes andfootnotes that provides explanatory material.These notes andfootnotes(excluding those in tables and figures)shall not beconsidered as requirements of the specification.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.NOTE1Sieve size is identified by its standard designation in Speci-fication E11.The alternative designation given in parentheses is forinformation only and does not represent a different standard sieve size.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C29/C29M Test Method for Bulk Density(“Unit Weight”)and Voids in AggregateC88/C88M Test Method for Soundness of Aggregates byUse of Sodium Sulfate or Magnesium SulfateC125 Terminology Relating to Concrete and Concrete Ag-gregatesC131/C131M Test Method for Resistance to Degradation ofSmall-Size Coarse Aggregate by Abrasion and Impact inthe Los Angeles MachineC136/C136M Test Method for Sieve Analysis of Fine andCoarse AggregatesC142/C142M Test Method for Clay Lumps and FriableParticles in AggregatesC294 Descriptive Nomenclature for Constituents of Con-crete AggregatesD8 Terminology Relating to Materials for Roads and Pave-mentsD75/D75M Practice for Sampling AggregatesD448 Classification for Sizes of Aggregate for Road andBridge ConstructionD692/D692M Specification for Coarse Aggregate for Bitu-minous Paving MixturesD693 Specification for Crushed Aggregate for MacadamPavements(Withdrawn 2008)3D1139/D1139M Specification for Aggregate for Single orMultiple Bituminous Surface TreatmentsD2489/D2489M Test Method for Estimating Degree of Par-ticle Coating of Asphalt MixturesD3319 Practice for the Accelerated Polishing of AggregatesUsing the British Wheel1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.50 onAggregate Specifications.Current edition approved Nov.1,2019.Published November 2019.Originallyapproved in 1997.Last previous edition approved in 2015 as D6155 15.DOI:10.1520/D6155-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 D3515 Specification for Hot-Mixed,Hot-Laid BituminousPaving Mixtures(Withdrawn 2009)3D3665 Practice for Random Sampling of Construction Ma-terialsD4215 Specification for Cold-Mixed,Cold-Laid BituminousPaving MixturesD4792/D4792M Test Method for Potential Expansion ofAggregates from Hydration ReactionsD4867/D4867M Test Method for Effect of Moisture onAsphalt Concrete Paving MixturesD5106 Specification for Steel Slag Aggregates for Bitumi-nous Paving MixturesD5711 Test Method for Determining the Adherent Coatingon Coarse Aggregates(Withdrawn 2012)3D5821 Test Method for Determining the Percentage ofFractured Particles in Coa

此文档下载收益归作者所有

下载文档
猜你喜欢
你可能关注的文档
收起
展开