ASTM_D_7505_-_D_7505M_-_17.pdf

Designation:D7505/D7505M17Standard Specification forSelf-Adhesive Polyester Fabric Reinforced Polymer ModifiedAsphalt Steep Slope Roll Roofing Surfaced with MineralGranules1This standard is issued under the fixed designation D7505/D7505M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers prefabricated,self-adhesive,polyester fabric reinforced,polymer-modified asphalt surfacedroll roofing products,with granule surfacing,designed forsteep slope applications.These products use polymer modifiersin their top and bottom coatings.These products have anadhesive bottom layer which is exposed by removal of apeel-away protective release paper or film sheet.1.2 The specified tests and property limits used to charac-terize the sheet materials are intended to establish minimumproperties.In-place roof system design criteria,such as fireresistance,field strength,impact/puncture resistance,materialcompatibility,uplift resistance,and others,are factors beyondthe scope of this material specification.Factors regarding thesuitability of specific roof constructions or application tech-niques are beyond this scope.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D903 Test Method for Peel or Stripping Strength of Adhe-sive BondsD1079 Terminology Relating to Roofing and WaterproofingD4977/D4977M Test Method for Granule Adhesion to Min-eral Surfaced Roofing by AbrasionD5147/D5147M Test Methods for Sampling and TestingModified Bituminous Sheet Material3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this specification,referto Terminology D1079.3.1.2 ultimate elongation,nthe elongation measured onthe load-elongation curve at which point the load has droppedto 5%of its maximum value,after the peak load has beenreached.4.Materials and Manufacture4.1 In the process of manufacture,the reinforcing mat ispermitted to be impregnated with asphalt or modified asphaltand is coated on its top and bottom sides with polymermodified asphalt coatings.The polymer modified asphaltcoatings are permitted to be compounded with a mineralstabilizer.The coating on the bottom side shall feature self-adhesive properties.4.2 The sheet is surfaced on the weather side with mineralgranules,except for any selvage.5.Physical Properties5.1 The sheet shall conform to the minimum physicalproperties prescribed in Table 1.5.2 The finished product shall not crack nor be so sticky asto cause tearing or other material damage upon being unrolled1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.02on Steep Roofing Products and Assemblies.Current edition approved July 1,2017.Published July 2017.Originally approvedin 2010.Last previous edition approved in 2010 as D7505/D7505M 10.DOI:10.1520/D7505_D7505M-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 at any product temperature between 4 and 60C 40 and 140For at a lower temperature if the manufacturer allows applica-tion at such lower temperature.5.3 The release paper,or film sheet,shall not tear duringremoval.6.Dimensions and Permissible Variations6.1 The width and area of the finished product shall conformto the following:6.1.1 The width of the roll