ASTM_D_713_-_12_2017.pdf

Designation:D71312(Reapproved 2017)Standard Practice forConducting Road Service Tests on Fluid Traffic MarkingMaterials1This standard is issued under the fixed designation D713;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers the determination of the relativeservice life of fluid traffic marking materials such as paint,thermoplastic,epoxy,and polyester products under actual roadconditions using transverse test lines.Materials under test areapplied under prescribed conditions and periodic observationsare made using prescribed performance criteria.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D711 Test Method for No-Pick-Up Time of Traffic PaintD913 Practice for Evaluating Degree of Traffic MarkingLine WearD6628 Specification for Color of Pavement Marking Mate-rialsE1710 Test Method for Measurement of RetroreflectivePavement Marking Materials with CEN-Prescribed Ge-ometry Using a Portable RetroreflectometerE2367 Test Method for Measurement of Nighttime Chroma-ticity of Pavement Marking Materials Using a PortableRetroreflection Colorimeter3.Significance and Use3.1 This practice is an accelerated evaluation of beadretention,retroreflectivity,daytime color,night time color,andwear characteristics of fluid traffic marking materials.It is usedto determine the useful life of such markings in the field.Thesame procedures are applicable to evaluating longitudinal linesto determine service life.4.Type and Location of Pavement for Tests4.1 Select sections where traffic is moderate and free-rollingwith no grades,curves,intersections,or access points nearenough to cause excessive braking or turning movements,where wear is uniform with full exposure to the sun throughoutdaylight hours,and there is good drainage.Select surfaces thatare representative of the pavements upon which the fluid trafficmarking material will be used in practice.Such surfacesinclude portland cement concrete,sheet asphalt,bituminousconcrete,rock asphalt,and bituminous surface treatment.5.Conditions at Time of Application5.1 Clean the test area thoroughly of all foreign material.Follow the pavement marking manufacturers recommendationfor the application of the pavement marking to be tested.Thisshould include the recommendations for air and pavementtemperature,material temperature,relative humidity,windchill,and wind speed.Application between 10 a.m.and 3 p.m.is recommended.During application record air and pavementtemperature,wind speed,and relative humidity hourly.6.Measurement of Wet Film Thickness6.1 To aid in obtaining the correct film thickness,a length ofroofing paper placed by the side of the road can be used.Placea rigid metal test panel on the roofing paper and in the path ofthe test line.A 300 by 300-mm(12 by 12-in.)metal panel 1.5mm(116in.)in thickness is satisfactory.Immediately after thetest line is applied by the motorized striper,read the wet filmthickness.If the wet film thickness is not satisfactory,adjust thespray pressure and repeat until the target wet film thickness is1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.44 on Traffic Coatings.Current edition approved Dec.1,2017.Published December 2017.Originallyapproved in 1943.Last previous edition approved in 2012 as D713 12.DOI:10.1520/D0713-12R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers t