分享
ASTM_D_6472_-_10.pdf
下载文档

ID:173614

大小:160.20KB

页数:10页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_6472_ _10
Designation:D647210Standard Specification forRecycled Glycol Base Engine Coolant Concentrate forAutomobile and Light-Duty Service1This standard is issued under the fixed designation D6472;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers the requirements for recycledethylene glycol base engine coolant concentrate and recycledpropylene glycol base engine coolant concentrate for use inautomobiles and light-duty vehicles.Committee D15 hasdeveloped this specification using experience,knowledge andresearch from recycling used aqueous base engine coolant andblends of used aqueous base engine coolant and virgin glycol.This standard does not apply to coolant produced from otherglycol sources such as medical waste,distillation bottoms,airplane/airport deicers and polyester production waste.Thisspecification provides a procedure for evaluating engine cool-ant recycling technologies through the recycling of a referencesynthetic used engine coolant.It also specifies the chemical,physical,and performance requirements for the recycled glycolbase engine coolant concentrate that is produced from thatprocedure.When used at 40 to 70 volume%in water,it willfunction effectively during both winter and summer.Thismaterial is intended to provide protection against freezing,boiling,and corrosion in automobile or other light-duty servicecooling systems.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are approximateequivalents and provided for information only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D512 Test Methods for Chloride Ion In WaterD516 Test Method for Sulfate Ion in WaterD1119 Test Method for Percent Ash Content of EngineCoolantsD1120 Test Method for Boiling Point of Engine CoolantsD1121 Test Method for Reserve Alkalinity of Engine Cool-ants and AntirustsD1122 Test Method for Density or Relative Density ofEngine Coolant Concentrates and Engine Coolants By TheHydrometerD1123 Test Methods for Water in Engine Coolant Concen-trate by the Karl Fischer Reagent MethodD1126 Test Method for Hardness in WaterD1176 Practice for Sampling and Preparing Aqueous Solu-tions of Engine Coolants orAntirusts for Testing PurposesD1177 Test Method for Freezing Point of Aqueous EngineCoolantsD1193 Specification for Reagent WaterD1287 Test Method for pH of Engine Coolants andAntirustsD1293 Test Methods for pH of WaterD1384 Test Method for Corrosion Test for Engine Coolantsin GlasswareD1881 Test Method for Foaming Tendencies of EngineCoolants in GlasswareD1882 Test Method for Effect of Cooling System ChemicalSolutions on Organic Finishes for Automotive VehiclesD2570 Test Method for Simulated Service Corrosion Testingof Engine CoolantsD2809 Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With En-gine CoolantsD2847 Practice for Testing Engine Coolants in Car and LightTruck ServiceD3306 Specification for Glycol Base Engine Coolant forAutomobile and Light-Duty ServiceD3634 Test Method for Trace Chloride Ion in Engine Cool-antsD4327 Test Method for Anions in Water by Suppressed IonChromatographyD4340 Test Method for Corrosion of Cast Aluminum Alloysin Engine Coolants Under Heat-Rejecting ConditionsD5827 Test Method for Analysis of Engine Coolant forChloride and Other Anions by Ion Chromatography1This specification is under the jurisdiction ofASTM Committee D15 on EngineCoolants and Related Fluids and is the direct responsibility of SubcommitteeD15.15 on Recycled Engine Coolant.Current edition approved April 1,2010.Published May 2010.Originallyapproved in 2000.Last previous edition approved in 2006 as D647206.DOI:10.1520/D6472-10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D5931 Test Method for Density and Relative Density ofEngine Coolant Concentrates and Aqueous Engine Cool-ants by Digital Density MeterD6129 Test Method for Silicon in Engine Coolant Concen-trates by Atomic Absorption SpectroscopyD6130 Test Method for Determination of Silicon and OtherElements in Engine Coolant by Inductively CoupledPlasma-Atomic Emission SpectroscopyD6208 Test

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开