分享
ASTM_D_6979_-_18.pdf
下载文档

ID:173248

大小:72.95KB

页数:3页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_6979_ _18
Designation:D697918Standard Test Method forPolyurethane Raw Materials:Determination of Basicity inPolyols,Expressed as Percent Nitrogen1This standard is issued under the fixed designation D6979;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method measures the basic constituents inpolyols that are soluble in glacial acetic acid and reactive withperchloric acid.Samples containing 0.3 10%nitrogen havebeen evaluated by this method.This test method is applicableto polyether polyols and polyether polyol blends that are usedin urethane reactions.(See Note 1.)1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.NOTE1This standard is equivalent to ISO 25761:08.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsE180 Practice for Determining the Precision of ASTMMethods for Analysis and Testing of Industrial and Spe-cialty Chemicals(Withdrawn 2009)3E691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 ISO Standards:4ISO 25761 PlasticsPolyols for use in the production ofpolyurethanesDetermination of basicity(total aminevalue),expressed as percent nitrogen3.Terminology3.1 DefinitionsFor definitions of terms used in this testmethod see Terminology D883.3.2 Definitions of Terms Specific to This Standard:3.2.1 percent nitrogenthe quantity of perchloric acid-titratable base,expressed as a weight percentage of nitrogen ina sample.4.Summary of Test Method4.1 The sample is dissolved in glacial acetic acid.Theresulting single-phase solution is titrated at room temperatureto a potentiometric end point with a standardized solution ofperchloric acid in acetic acid.Results are reported as percentnitrogen.5.Significance and Use5.1 This test method is suitable for quality control,as aspecification test,and for research.The results are measures ofbatch-to-batch uniformity and are useful in estimating reactiv-ity.5.1.1 The percent nitrogen can be used to characterize apolyol or indicate amounts of certain components in a polyolblend.5.1.2 It is permissible to also express the results in equiva-lents of base per gram of sample,if desired.6.Apparatus6.1 Potentiometric Automatic Titrator6.2 Autotitrator Buret with Dosing Device,20-mL6.3 pH Glass Electrode and Reference Electrode or aCombination Glass Electrode1This test method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.22 on Cellular Materials-Plastics and Elastomers.Current edition approved Aug.1,2018.Published August 2018.Originallyapproved in 2003.Last previous edition approved in 2013 as D6979-13.DOI:10.1520/D6979-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.4 Analytical Balances,capable of weighing to the nearest0.01g and 0.0001 g6.5 Magnetic Stirrer/Hotplate7.Reagents and Materials7.1 Purity of ReagentsUse reagent-grade chemicals in alltests.Unless otherwise indicated,it is intended that all reagentsconform to the specifications of the Committee on AnalyticalReagents of the American Chemical Society where suchspecifications are available.5It is permissible to use othergrades provided it is first ascertained that the reagent is ofsuffic

此文档下载收益归作者所有

下载文档
猜你喜欢
你可能关注的文档
收起
展开