ASTM_D_8218_-_20.pdf

Designation:D821820Standard Guide forIntrusion Detection System(IDS)1This standard is issued under the fixed designation D8218;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide covers the recommended intrusion detectionsystem(IDS)for protecting resin cannabis,resin cannabisproducts,resin cannabis waste,currency,people,property,andassets.1.2 UnitsThe values stated in inch-pound units are to beregarded as standard.The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Terminology2.1 Definitions of Terms Specific to This Standard:2.1.1 beam alarm,nelectronic device that detects anyinterruption to the signal between a transmitter and receiver.2.1.2 contact alarm,nactivated when the device isseparated,such as opening.2.1.3 duress code,ncode that,when entered,generates asilent alarm signal indicating that a person is being forced toturn off the alarm,also known as a holdup alarm.2.1.4 failure notification,nprovides an audible,text,orvisual notification of any failure in the systems.2.1.5 glass break,naudio sensor to pick up the actualfrequency of broken glass.2.1.6 holdup alarm,ndevice activated to signal a robberyin progress,which shall generate a silent alarm.2.1.7 Internet protocol,IP,ndata sent over the Internet orother network.2.1.8 intrusion detection system,IDS,nmotion detection,door and window contact alarm,and glass-break sensor.2.1.9 motion detection,npassive infrared to survey thearea and sounds an audible notification alarm when a person orobject moves into the protected space.2.1.10 panic alarm,nkeypad code,button,or device foruse in a life-threatening or emergency situation that shall bemanually activated in any emergency when security,police,orfire response is needed.2.1.11 perimeter alarm,noutdoor alarms including fencedetection,underground cable,microwave and infrared sensors.2.1.12 two-factor authentication,nat least two of thefollowing:an access control credential(for example,badge,FOB,wireless device),personal identification number(PIN),or biometric,or combinations thereof.2.1.13 uninterruptible power supply,UPS,nensure con-tinuous operation of the IDS using a surge protector with abuilt-in backup battery.3.Significance and Use3.1 The intrusion detection system(IDS)safeguards variousareas considered critical to operations.Intrusion detectiondevices include but are not limited to,door or window contactalarms that are activated when the device is separated,such asopening;and motion detection technology that uses a passiveinfrared to survey the area and sounds an audible notificationalarm when a person or object moves into the protected space.Also included are glass-break detectors that use an audiosensor to pick up the actual frequency of broken glass.If theglass-break detector“hears”broken glass,an alarm is acti-vated.If any of the devices are triggered when the system isarmed,an alert is sent to a 24-h monitoring area for notifica-tion.4.Summary of Guide4.1 The following intrusion detection system(IDS)technologies,equipment,capabilities,and procedures are in-dustry best-practice-based.1This guide is under the jurisdiction of ASTM Committee D37 on Cannabis andis the direct responsibility of Subcommittee D37.05 on Security and Transportation.Current edition approved Feb.1,2020.Published February 2020.DOI:10.1520/D8218-20.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.4.1.1 An on-or off-site monitoring station designed tomanage and monitor all intrusion detection information,alongwith receiving and sending notifications of all alarm activa-tions.4.1.2 Using intrusion detection technology,select personnelwith designated backups are able to monitor and assignappropriate access.4.