ASTM_D_8013_-_16_2021.pdf

Designation:D801316(Reapproved 2021)Standard Guide forEstablishing a Recycle Program for Roof Coverings,Roofing Membrane,and Shingle Materials1This standard is issued under the fixed designation D8013;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide provides information for the development ofa program to reduce roof covering waste.The recycled roofcoverings and any scrap roof cover materials may be repro-cessed back into new roof coverings,into other roofingproducts,or into products other than roofing.This guide doesnot comment on the use or the inclusion of other recycled orrecovered materials which may be used to increase the totalamount of recycle material.1.2 This guide addresses terminology,logistics,qualityassurance,separation,or segregation in the recycling processof materials.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1079 Terminology Relating to Roofing and WaterproofingD7209 Guide for Waste Reduction,Resource Recovery,andUse of Recycled Polymeric Materials and Products(With-drawn 2015)32.2 UL Standard:4UL 2809 Environmental Claim Validation Procedure forRecycled Content2.3 ICC Standard:5ICC International Building Code,current version3.Terminology3.1 DefinitionsFor definitions of roofing terms,see Ter-minology D1079.For definitions of recycling and recoveryterms,see Guide D7209.3.2 Definitions of Terms Specific to This Standard:3.2.1 bale,nwaste that is compacted and secured as abundle to facilitate handling,storage,and transportation.3.2.2 bulk box,nalso known as bulk bin,skid box,totebox,or Gaylord,these are normally pallet size containers usedfor storing and shipping bulk quantities constructed of corru-gated fiberboard,either double or triple walled.3.2.3 certificate of composition disclosure,ncertificatedescribing certain properties of a recovered material from anexternal source,its formation and source,and the specificmaterial shipment to which it applies.3.2.3.1 DiscussionExamples of CCD information includepolymer,molecular weight,percentage of inorganic material,contamination type and level,strength,modulus,impact andother mechanical properties;code or designation identifyingthe formulation and source information.3.2.4 chemical recycling,nprocessing of recovered mate-rial into a secondary raw material or product,with a significantchange to the chemical structure of the material(such ascracking,gasification,and depolymerization),but excludingenergy recovery or incineration.3.2.5 collection,nlogistical process of moving waste fromits source to a place where it can be recovered.3.2.6 contaminant,nunwanted substance or material de-fined according to the intended use.1This guide is under the jurisdiction of ASTM Committee D08 on Roofing andWaterproofing and is the direct responsibility of Subcommittee D08.24 on Sustain-ability.Current edition approved Jan.1,2021.Published January 2021.Originallyapproved in 2016.Last previous edition approved in 2016 as D8013 16.DOI:10.1520/D8013-16R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Underwriters Laboratories(UL),2600 N.W.Lake Rd.,Camas,WA 98607-8542,http:/.5Available from International Code Council(ICC),500 New Jersey Ave.,NW,6th Floor,Washington,DC 20001,http:/www.iccsafe.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.2.7 fluff,nfilament like by-product from recycling suchas fiberglass or polyester reinforcement,felt backing,andsimilar materials.3.2.8 impurity,nsee contaminant.3.2.9 landfill,nwaste disposal site for the depos