ASTM_D_7910_-_14_2021.pdf

Designation:D791014(Reapproved 2021)Standard Practice forCollection of Fungal Material From Surfaces by Tape Lift1This standard is issued under the fixed designation D7910;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice describes the protocols for collection ofsurface samples using tape lifts and their delivery to thelaboratory.1.2 The purpose of this practice is to support the fieldinvestigator in differentiating fungal materials from non-fungalmaterial such as scuffs,soot deposits,stains,pigments,dust,efflorescence,adhesives,and water stains.1.3 The samples collected by this practice are appropriatefor either qualitative or quantitative analysis by direct micros-copy.1.4 This practice does not address building occupantexposures,or occupant health risks.1.5 This practice does not address the development of aformal hypothesis or the establishment of sampling objectives.1.6 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1356 Terminology Relating to Sampling and Analysis ofAtmospheresD4840 Guide for Sample Chain-of-Custody ProceduresD6044 Guide for Representative Sampling for Managementof Waste and Contaminated Media3.Terminology3.1 DefinitionsFor terminology not defined herein,referto Terminology D1356.3.2 Definitions of Terms Specific to This Standard:3.2.1 area(surface,sampled),na defined,measured ex-tent of surface sampled.3.2.2 chain of custody(COC),na document that providesfor the traceable transfer of field samples to the analyticallaboratory.It may or may not be combined with the field datasheet.D48403.2.3 direct microscopy analysis,nact of assessing micro-organisms(if present)using an optical compound microscope.3.2.4 field data sheet,na record of varying names thatprovides a reference document for information directly relatedto the sample collection event,including pre-and post-calibration data.3.2.5 fungal material,nfungal spores,hyphae,and repro-ductive structures.3.2.6 fungal structure(sing.),ncollective term for frag-ments or groups of fragments from fungi,including but notlimited to conidia,conidiophores,hyphae,and spores.3.2.7 fungi(pl.),neukaryotic,heterotrophic,absorptiveorganisms that usually develop a rather diffuse,branched,tubular body(that is,network of hyphae)and usually repro-duce by means of spores.3The terms mold and mildew arefrequently used by laypersons when referring to various fungalcolonization.1This practice is under the jurisdiction ofASTM Committee D22 on Air Qualityand is the direct responsibility of Subcommittee D22.08 on Assessment,Sampling,and Analysis of Microorganisms.Current edition approved Sept.1,2021.Published September 2021.Originallyapproved in 2014.Last previous edition approved in 2014 as D7910 14.DOI:10.1520/D7910-14R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Kendrick,B.,The Fifth Kingdom,Focus Publishing/R.Pullins&Co,2008.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.2.8 sample,na portion of material that is taken fortesting or record purposes.D60444.Significance and Use4.1 This practice defines a consistent procedure for collect-ing surface material using clear,transparent,single sidedadhesive collection medium,typically tape(also known as tapelift).4.2 A tape lift sample collected according to this practice isintended to be used to assess the material present at onespecific location on a surface for fungal content.4.3 A tape lift sample collected from a point of interest canbe used for qualitative analysis or to