ASTM_D_7330_-_22.pdf

Designation:D733022Standard Test Method forAssessment of Surface Appearance Change in Pile FloorCoverings Using Standard Reference Scales1This standard is issued under the fixed designation D7330;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1This test method covers the assessment of changes ofsurface appearance of pile floor coverings after exposure toactual or simulated foot traffic.This test method applies to pileyarn floor coverings that are,or have been,installed;laboratoryfloor-trafficked samples;or textiles floor coverings traffickedby mechanical traffic simulators.The subjective assessment isfacilitated by use of reference scales that are based on digitalimages of representative pile yarn floor covering styles andconstructions.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD5252 Practice for the Operation of the Hexapod TumbleDrum TesterD5417 Practice for Operation of the Vettermann DrumTesterD5684 Terminology Relating to Pile Floor CoveringsD6119 Practice for Creating SurfaceAppearance Changes inPile Yarn Floor Covering from Foot TrafficD6962 Practice for Operation of a Roller Chair Tester forPile Yarn Floor CoveringsE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.Terminology3.1 For definitions of terms relating to Pile Floor Coverings,refer to the Terminology D5684.3.2 The following terms are relevant to this standard:carpet,crushing cut pile yarn floor covering,finished,finished pileyarn floor covering,loss of tuft definition,matting,pile,pileyarn floor covering,textile floor covering.3.3 For definitions of other terms related to textiles,refer toTerminology D123.4.Summary of Test Method4.1 The floor covering shall be tested in a mechanical wearsimulator or tested under controlled laboratory foot traffic testsreferenced in Practices D5252,D5417,D6119,and D6962.Thetested floor covering shall then be assessed for surface appear-ance change by comparing unexposed controls to the exposedsample by using the appropriate Appearance Change GradingScale.5.Significance and Use5.1 The determination of surface appearance change in pileyarn floor covering is useful in quality and cost control duringmanufacture of pile yarn floor covering.This test method isconsidered satisfactory for acceptance testing of commercialshipments because current estimates of between laboratoryprecision are acceptable,and this test method is commonlyused in trade for acceptance testing.5.2 If there are differences of practical significance betweenreported test results for two laboratories(or more),compara-tive tests should be performed to determine if there is astatistical bias between them,using competent statistical assis-tance.As a minimum,use the samples for such comparative1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.21 on Pile Floor Coverings.Current edition approved June 15,2022.Published July 2022.Originallyapproved in 2007 as D7330-07.Last previous edition published in 2015 asD7330-15.DOI:10.1520/D7330-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1tests that are as homogenous as possible,drawn from the samelot of material