ASTM_D_644_-_99_2007.pdf

Designation:D644 99(Reapproved 2007)An American National StandardStandard Test Method forMoisture Content of Paper and Paperboard by Oven Drying1This standard is issued under the fixed designation D644;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This test method covers the determination of the mois-ture in all papers,paperboards,and paperboard and fiberboardcontainers,except those containing matter other than water thatis volatile at 105C.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1This test method is technically equivalent to TAPPI T412 83.2.Referenced Documents2.1 ASTM Standards:2D585 Practice for Sampling and Accepting a Single Lot ofPaper,Paperboard,Fiberboard,and Related Product3.Significance and Use3.1 The moisture content of paper and paperboard mayaffect the purchase cost and can also have an effect upon theperformance of the paper in a given application since moisturecontent can affect properties including,but not limited totensile strength,tearing resistance,dimensional instability,permanence,printability,flexibility,and runability on varioustypes of paper processing machinery and equipment.Knowl-edge of moisture content is necessary to calculate,to a drybasis,analytical results obtained from test specimens weighedat ambient or conditioned moisture content.4.Apparatus4.1 Weighing Container,airtight,for weighing the specimenbefore and after drying.A glass weighing bottle with a groundstopper is suitable for specimens of the order of 2 g.Theweighing bottle may be of either high or low form;a volumeof about 100 mL is appropriate.An airtight metal container,preferably containing a light-weight large-mesh wire basket,issuitable for larger specimens,particularly those over 10 g.4.2 Thermometer,to indicate the temperature of the dryingoven.This thermometer shall include the temperature rangefrom 100 to 110C,and its scale shall be divided in 1intervals.4.3 Drying Oven,constant-temperature,equipped withmeans for ensuring adequate temperature control and aircirculation,a means to separate the heating coils from thesample containment area(generally the oven bottom plate),and preferably equipped with means for drying the air enteringthe oven.4.4 Chemical Balance,sensitive to 1 mg,for weighingspecimens of 2 g and under,and sensitive to 0.05%of theoriginal weight of the specimen for larger specimens.4.5 Desiccator,in which weighing containers and speci-mens are cooled after drying.It is recommended that anhy-drous alumina(indicator grade)be used as the desiccant.5.Test Specimens5.1 When moisture is determined for the purpose of calcu-lating the results of a chemical analysis of paper or board on amoisture-free basis,the test specimens shall weigh not lessthan 1 g,and preferably not less than 2 g each.At the time ofinitial weighing,these specimens shall be in moisture equilib-rium with the samples being analyzed.5.2 When moisture is determined for the purpose of calcu-lating the amount of moisture in a shipment,the test specimensshall weigh not less than 50 g each,and shall be taken fromsamples obtained in accordance with Practice D585.5.3 When moisture is determined on combined board orcontainers that are to be tested for other physical properties,test specimens shall weigh approximately 50 g,and shall betaken so as to be representative of the material being tested.Inthe case of containers,specimens shall be cut from unsealedsections,and preferably from unprinted sections,of the con-tainer,and shall be taken from each type of container beingtested.1This test method is under the jurisdiction of ASTM Committee D06 on Paperand Paper Products and is the direct responsibility of Subcommittee D06.92 onStandard Documents Relating to Paper and Paper Products.Current edition approved Dec.1,2007.Published December 2007.Originallyapproved in 1955.Last previous edition approved in 2002 as D644 99(2002).DOI:10.1520/D0644-99R07.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.NOTICE:This standard has either been superseded and replaced by a new version or withdrawn.Contact ASTM International(www.astm.org)for the latest information.6.Procedure6.1 Determine the tar