分享
ASTM_D_6881_-_D_6881M_-_03_2020.pdf
下载文档

ID:171928

大小:149.45KB

页数:5页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_6881_ _D_6881M_ _03_2020
Designation:D6881/D6881M03(Reapproved 2020)Standard Classification forStandard Plastics Industry Bulk Box/Pallet Unit SizeClassified By Bulk Density1This standard is issued under the fixed designation D6881/D6881M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONAn ad-hoc survey in 2000 showed about 40 different box sizes in use by the plastic resin industry;the purpose for this classification is to quantify a box/pallet unit size acceptable for this industry withinthe limits of the scope.1.Scope1.1 This classification covers containers used to hold plasticresins with bulk density(Test Methods D1895)of 27 to 39lb/ft3(0.432 to 0.625 g/cm3).1.2 This classification does not apply to any plastic resinswith bulk density below 27 lb/ft3(0.432 g/cm3)or above39lb/ft3(0.625 g/cm3).1.3 This classification does not apply to bulk boxes contain-ing hazardous materials.1.4 This classification does not address box/pallet unitiza-tion requirements.1.5 This classification does not address requirements ofplastic bag liners normally placed inside the corrugated bulkbox before filling with plastic resin.1.6 This classification does not address tamping,shaking,orother compression methods of the resin filled bulk box tocondense entrained air and increase headspace in the bulk box.1.7 This classification does not address blocking and brac-ing or other shipping requirements normally associated withbulk box unit deliveries.1.8 This classification does not address filled bulk box/palletunit stack height.1.9 This classification does not address international ship-ping regulations of bulk box/pallet units.1.10 This classification does not address pallet openingsizes for pallet trucks.1.11 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.12 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.13 This classification offers an organized collection ofinformation or a series of options and does not recommend aspecific course of action.This document cannot replace edu-cation or experience and should be used in conjunction withprofessional judgement.Not all aspects of this classificationmay be applicable in all circumstances.This ASTM standard isnot intended to represent or replace the standard of care bywhich the adequacy of a given professional service must bejudged,nor should this document be applied without consid-eration of a projects many unique aspects.The word“stan-dard”in the title of this document means only that thedocument has been approved through the ASTM consensusprocess.1.14 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.1This classification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.12 on ShippingContainers,Crates,Pallets,Skids and Related Structures.Current edition approved Oct.1,2020.Published October 2020.Originallyapproved in 2003.Last previous edition approved in 2013 as D6881/D6881M 03(2013).DOI:10.1520/D6881_D6881M-03R20.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.12.Referenced Documents2.1 ASTM Standards:2D1895 Test Methods for Apparent Density,Bulk Factor,andPourability of Plastic Materials3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 bulk box,plastic resin,na container used to enclose,protect,hold,and transport plastic resin,with net weights ofabout 1000 to 1600 lb(453.6 to 725.7 kg);it will havesemi-rigid sidewalls that resist bulging of the sidewall whenloaded,retain the approximate size of the empty assembledbox,and prevent collapse of the container during removal ofthe product.3.1.1.1 DiscussionNormally,the box is placed on a palletor skid,fill

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开