分享
ASTM_D_8355_-_21.pdf
下载文档

ID:171924

大小:130.15KB

页数:8页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_8355_ _21
Designation:D835521Standard Test Methods forFlammability of Electrical Insulating Materials Used forSleeving or Tubing1This standard is issued under the fixed designation D8355;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.NOTESubsection 1.2.1 was added and the yeardate was changed on March 31,2021.1.Scope1.1 This is a fire-test-response standard.1.2 This fire test response standard contains various testsapplicable to electrical insulation materials used for sleeving orfor tubing(including heat-shrinkable tubing).1.2.1 Test methods C and D are applicable to heat-shrinkable tubing only.1.3 Use the values stated in SI units in referee decisions;seeIEEE/ASTM SI-10.The values given in parentheses after SIunits are provided for information only and are not consideredstandard.1.4 This standard is used to measure and describe theresponse of materials,products,or assemblies to heat andflame under controlled conditions,but does not by itselfincorporate all factors required for fire hazard or fire riskassessment of the materials,products,or assemblies underactual fire conditions.1.5 Fire testing is inherently hazardous.Adequate safe-guards for personnel and property shall be employed inconducting these tests.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D350 Test Methods for Flexible Treated Sleeving Used forElectrical InsulationD876 Test Methods for Nonrigid Vinyl Chloride PolymerTubing Used for Electrical InsulationD1711 Terminology Relating to Electrical InsulationD2671 Test Methods for Heat-Shrinkable Tubing for Elec-trical UseD2903 Specification for Crosslinked Chlorinated PolyolefinHeat-Shrinkable Tubing for Electrical InsulationD3144 Specification for Crosslinked Poly(Vinylidene Fluo-ride)Heat-Shrinkable Tubing for Electrical InsulationD3150 Specification for Crosslinked and NoncrosslinkedPoly(Vinyl Chloride)Heat-Shrinkable Tubing for Electri-cal InsulationD5025 Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic MaterialsD5207 Practice for Confirmation of 20-mm(50-W)and125-mm(500-W)Test Flames for Small-Scale BurningTests on Plastic MaterialsE176 Terminology of Fire Standards2.2 ISO Standard:3ISO 13943 Fire Safety Vocabulary2.3 Federal Standard:4PPP-T-45D Federal Specification for Tape;Paper,Gummed(Kraft)2.4 UL Standards:5UL 224 Extruded Insulated TubingUL 1441 Coated Electrical Sleeving1These test methods are under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and are the direct responsibility ofSubcommittee D09.17 on Fire and Thermal Properties.Current edition approved March 31,2021.Published April 2021.Last previousedition approved in 2020 as D8355 20.DOI:10.1520/D8355-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from International Organization for Standardization(ISO),ISOCentral Secretariat,BIBC II,Chemin de Blandonnet 8,CP 401,1214 Vernier,Geneva,Switzerland,http:/www.iso.org.4Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.5Available from Underwriters Laboratories(UL),UL Headquarters,333 Pfing-sten Road,Northbrook,IL,60062,http:/.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1UL 2556 Wire and Cable Test Methods3.Terminology3.1 Definitions:3.1.1 For definitions of terms relating to electrical andelectronic insulating materials,the definitions in these testmethods are in accordance with Terminology D1711.For termsrelating to fire,the definitions in this test method are inaccordance with Terminology E176 and ISO 13943.In case ofconflict,the definitions

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开