ASTM_D_8102_-_17.pdf

Designation:D810217Standard Practice forManufacturing Quality Control of Geotextiles1This standard is issued under the fixed designation D8102;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers the manufacturing quality controlof geotextiles,describing types of tests,the proper testmethods,minimum testing frequencies,and best practices forsampling.1.2 This practice does not address manufacturing qualityassurance,product acceptance testing,or conformance testing.These are independent activities taken by organizations otherthan the geotextiles manufacturer.1.3 This practice is intended to aid manufacturers,suppliers,purchasers,installers,and end users of geotextiles in establish-ing a minimum level of effort for maintaining quality control.1.4 This practice covers procedures for sampling geotextilesfor the purpose of manufacturing quality control(MQC).Theseprocedures are designed to ensure that the correct number ofrepresentative samples are obtained and properly reported bythe manufacturer.1.5 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD4354 Practice for Sampling of Geosynthetics and RolledErosion Control Products(RECPs)for TestingD4355 Test Method for Deterioration of Geotextiles byExposure to Light,Moisture and Heat in a Xenon ArcType ApparatusD4491 Test Methods for Water Permeability of Geotextilesby PermittivityD4533 Test Method for Trapezoid Tearing Strength of Geo-textilesD4595 Test Method for Tensile Properties of Geotextiles bythe Wide-Width Strip MethodD4632 Test Method for Grab Breaking Load and Elongationof GeotextilesD4751 Test Methods for Determining Apparent OpeningSize of a GeotextileD5261 Test Method for Measuring Mass per Unit Area ofGeotextilesD6241 Test Method for Static Puncture Strength of Geotex-tiles and Geotextile-Related Products Using a 50-mmProbe2.2 American National Standard:3ANSI/ASQ Z1.9-2008 Sampling Procedures and Tables forInspection by Variables for Percent Nonconforming3.Terminology3.1 Definitions:3.1.1 For definitions of other textile terms used in thisstandard,refer to Terminology D123.3.2 Organizational Definitions:3.2.1 installer,nparty who installs,or facilitates installa-tion of,any materials purchased from manufacturers or sup-pliers.3.2.2 manufacturer,ngroup,corporation,partnership,orindividual that manufactures a product.3.2.3 purchaser,nperson,company,or organization thatpurchases any materials or work to be performed.3.2.4 supplier,nparty who supplies materials or services.3.3 Sampling Definitions:3.3.1 lot(geotextile lot),nthe amount of geotextile pro-duced per style type under the same standard operatingconditions during a specific period of time not to exceed twelveconsecutive months.3.3.2 lot summary,na lot-specific report that shows allsequential sample roll test results and the associated lot1This practice is under the jurisdiction of ASTM Committee D35 on Geosyn-thetics and is the direct responsibility of Subcommittee D35.01 on MechanicalProperties.Current edition approved Feb.15,2017.Published March 2017.Originallyapproved in 2017.DOI:10.1520/D8102-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Society for Quality(ASQ),600 N.Plankinton Ave.,Milwaukee,WI 53203,http:/www.asq.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 statistics,including the following information:typical value(mean)minimum,maximum,standard deviation,and MARVfor each test property.3.3.3 MARV,nthe minimum average roll value(MARV)for the geosynthetic,defined as the average value minus two(2)standard deviations from documented quality control testresults for a defined lot of production,sampled in accordancewith Table 1 of Practice D4354.3.3.4 maximum test value,nthe maximum test value forthe geosynthetic,def