ASTM_D_8104_-_17.pdf

Designation:D810417Standard Guide forDetermining Coating Qualification Test Data Applicability1This standard is issued under the fixed designation D8104;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 The purpose of this guide is to identify evaluationvariables that can be used to determine whether existingcoating qualification test data(for example,design basisaccident or DBA,chemical resistance,fire resistance,thermalconductivity,etc.)meet the respective nuclear power plantqualification requirements or whether requalification is re-quired.Guidance on developing a coating qualification testplan/procedure to qualify a new coating is beyond the scope ofthis standard.1.2 This guide is intended for use in new construction andfor refurbishing existing coating systems applied to concreteand metal substrates within containment.1.3 This guide is intended for the use by,or under thesupervision of,a person knowledgeable in coating technologyand coatings used in CSL I applications,such as a personmeeting the requirements of Guide D7108 or equivalent.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D3911 Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design BasisAccident(DBA)ConditionsD4060 Test Method for Abrasion Resistance of OrganicCoatings by the Taber AbraserD4082 Test Method for Effects of Gamma Radiation onCoatings for Use in Nuclear Power PlantsD4258 Practice for Surface Cleaning Concrete for CoatingD4259 Practice for Abrading ConcreteD4260 Practice for Liquid and Gelled Acid Etching ofConcreteD4538 Terminology Relating to Protective Coating andLining Work for Power Generation FacilitiesD4541 Test Method for Pull-Off Strength of Coatings UsingPortable Adhesion TestersD5139 Specification for Sample Preparation for Qualifica-tion Testing of Coatings to be Used in Nuclear PowerPlantsD5144 Guide for Use of Protective Coating Standards inNuclear Power PlantsD7108 Guide for Establishing Qualifications for a NuclearCoatings SpecialistE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE1269 Test Method for Determining Specific Heat Capacityby Differential Scanning CalorimetryE1530 Test Method for Evaluating the Resistance to Ther-mal Transmission of Materials by the Guarded Heat FlowMeter TechniqueG14 Test Method for Impact Resistance of Pipeline Coatings(Falling Weight Test)1This guide is under the jurisdiction of ASTM Committee D33 on ProtectiveCoating and Lining Work for Power Generation Facilities and is the directresponsibility of Subcommittee D33.02 on Service and Material Parameters.Current edition approved March 1,2017.Published April 2017.DOI:10.1520/D8104-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.2 Federal Standards:310CFR50 Ultimate design basisAppendix ACriterion 4 Environmental and Dynamic Ef-fectsAppendix BPart III Design ControlAppendix BPart XI Test Control2.3 U.S.NRC Standards:4USNRC Regulatory Guide 1.54 Service Level I,II,and IIIProtective Coatings Applied to Nuclear Power PlantsUSNRC APCSB 9.5-1,Branch Technical Position APCSB9.5-1 Guidelines for Fire Protection for Nuclear PowerPlants2.4 ANSI Standards:5ANSI N101.2 Protective Coatings(Paints)for Light WaterNuclear Reactor Containment Facilities2.5 SSPC Standards:6SSPC-SP 5 White Metal Blast CleaningSSPC-SP 6 Commercial Blast Clean