分享
ASTM_D_7275_-_07_2018.pdf
下载文档

ID:171227

大小:69.93KB

页数:3页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_7275_ _07_2018
Designation:D727507(Reapproved 2018)Standard Test Method forTensile Properties of Bituminous Geomembranes(BGMs)1This standard is issued under the fixed designation D7275;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is used to measure the tensile proper-ties of bituminous geomembranes(BGMs)using a dumbbell-shaped specimen.1.2 The values stated in SI units are to be regarded asstandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D638 Test Method for Tensile Properties of PlasticsD4354 Practice for Sampling of Geosynthetics and RolledErosion Control Products(RECPs)for TestingD4439 Terminology for GeosyntheticsD6455 Guide for the Selection of Test Methods for Prefab-ricated Bituminous Geomembranes(PBGMs)3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 prefabricated bituminous geomembrane(BGM),namaterial fabricated in a plant and consisting principally ofnonwoven geotextile,impregnated by a blend of oxidized orpolymer-modified bitumen incorporating filler.3.2 For definitions of other terms used in this test method,refer to Terminology D4439.4.Significance and Use4.1 This method is used to evaluate the tensile properties ofBGMs.It can be used for manufacturing quality control oracceptance testing.4.2 This test method uses a dumbbell specimen.The shapeand dimensions of the specimen are defined in this standard.No other shape or dimensions are allowed.Other mechanicalproperties of BGMs may be measured using different testmethods.Refer to Guide D6455.4.3 The reported properties are the maximum strength andelongation at maximum strength.5.Apparatus5.1 Tensile instrumentation shall meet the requirementsoutlined in Test Method D638.5.2 GripsOne of the grips must be self-aligning to com-pensate for uneven distribution of force across the specimen.The clamping force and the clamp surfaces shall hold thespecimen firmly without causing damage.5.3 Grip FacesGrip faces shall be a minimum of 50 mm(2 in.)wide and a minimum of 50 mm(2 in.)in length.Smoothrubber,fine serrated,or coarse serrated grip faces have all beenfound to be suitable for testing BGMs.If needed,the use of asilicone-coated paper to help holding the specimen ends intothe grips is recommended.The silicone-coated side is to beused in contact with the specimen.6.Sampling and Test Specimens6.1 Sampling shall be conducted according to PracticeD4354.6.2 Take a sample that will exclude material from the outerwrap of the roll or the inner wrap around the core.In the casewhere the sample is taken at the production site,material fromthe outer wrap may be used if it is undamaged.6.3 Test SpecimensPrepare five specimens with the lengthof the specimen parallel to the machine direction(MD)and fivespecimens with the length parallel to the cross-machine direc-tion(XD).1This test method is under the jurisdiction of ASTM Committee D35 onGeosynthetics and is the direct responsibility of Subcommittee D35.10 on Geomem-branes.Current edition approved Feb.1,2018.Published February 2018.Originallyapproved in 2006.Last previous edition approved in 2012 as D7275 07(2012).DOI:10.1520/D7275-07R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.4 The specimens shall be cut using an appropriate die tothe shape,dimensions,and tolerances presented in Fig.1.7.Conditioning and Testing7.1 Samples shall be conditioned for at least 24 h at 21 62 C(70 6 4 F)and 50 to 70%relative humidity.Thesamples shall be conditioned flat and shielded from the sun

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开