ASTM_D_715_-_86_2020.pdf

Designation:D71586(Reapproved 2020)Standard Test Methods forAnalysis of Barium Sulfate Pigment1This standard is issued under the fixed designation D715;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover the analysis of barium sulfatepigment.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D185 Test Methods for Coarse Particles in PigmentsD280 Test Methods for Hygroscopic Moisture(and OtherMatter Volatile Under the Test Conditions)in PigmentsD1193 Specification for Reagent WaterD1208 Test Methods for Common Properties of CertainPigmentsE832 Specification for Laboratory Filter Papers3.Significance and Use3.1 These test methods are used to determine the purity ofbarium sulfate and to determine the concentration of knownimpurities.This information is useful to producers and users asan aid in the manufacture of coatings.4.Purity of Reagents4.1 Reagent grade chemicals shall be used in all tests.Unless otherwise indicated,it is intended that all reagents shallconform to the specifications of the Committee on AnalyticalReagents of the American Chemical Society,where suchspecifications are available.3Other grades may be used,pro-vided it is first ascertained that the reagent is of sufficientlyhigh purity to permit its use without lessening the accuracy ofthe determination.4.2 Unless otherwise indicated,references to water shall beunderstood to mean reagent water conforming to Type II ofSpecification D1193.BARIUM SULFATE5.Reagents5.1 Ammonium Hydroxide(sp gr 0.90)Concentrated am-monium hydroxide(NH4OH).5.2 Ammonium Sulfate(NH4)2SO4).5.3 Hydrochloric Acid(sp gr 1.19)Concentrated hydro-chloric acid(HCl).5.4 Hydrochloric Acid(1+1)Mix equal volumes of con-centrated HCl(sp gr 1.19)and water.5.5 Methyl Red Indicator SolutionDissolve 0.2 g ofmethyl red in 100 mL of methanol,ethanol,or isopropanol.5.6 Sodium Carbonate Solution(30 g/L)Dissolve 30 g ofNa2CO3in water and dilute to 1 L.6.Procedure6.1 Weigh to 0.1 mg approximately 0.5 g of the sample intoa platinum crucible,add 3 g of Na2CO3,mix thoroughly,andfuse until the melt is clear.Allow the melt to cool and thenleach in a platinum dish with hot water until it is entirelydisintegrated.Filter on a close-texture paper and wash thor-oughly with hot Na2CO3solution(30 g/L).1These test methods are under the jurisdiction of ASTM Committee D01 onPaint and Related Coatings,Materials,and Applications and are the directresponsibility of Committee D01.31 on Pigment Specifications.Current edition approved June 1,2020.Published June 2020.Originallyapproved in 1943.Last previous edition approved in 2014 as D715 86(2014).DOI:10.1520/D0715-86R20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3ACS Reagent Chemicals,Specifications and Procedures for Reagents andStandard-Grade Reference Materials,American Chemical Society,Washington,DC.For suggestions on the testing of reagents not listed by the American ChemicalSociety,see Analar Standards for Laboratory Chemicals,BDH Ltd.,Poole,Dorset,U.K.,and the United States Pharmacopeia and National Formulary,U.S.Pharma-copeial Convention,Inc.(USPC),Rockville,MD.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.6.2 Transfer the filter paper containing the insoluble carbon-ates to a 250-mL beaker and acidify with concentrated HCl(spgr 1.19).Wash the fusion crucible with HCl(sp gr 1.19)so thatno barium is lost.Boil the solution,filter into a 600-mL beaker,and wash well with water.Add methyl red indicator solution,and