分享
ASTM_D_6977_-_19.pdf
下载文档

ID:170994

大小:114.10KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_6977_ _19
Designation:D697719Standard Specification forPolychloroprene Examination Gloves for MedicalApplication1This standard is issued under the fixed designation D6977;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification provides certain requirements forpolychloroprene rubber gloves used in conducting medicalexaminations and diagnostic and therapeutic procedures.1.2 This specification covers polychloroprene rubber exami-nation gloves that fit either hand,paired gloves,and gloves bysize.It also provides for packaged sterile or non-sterile or bulknon-sterile polychloroprene rubber examination gloves.1.3 This specification is similar to that of D3578 StandardSpecification for Rubber Examination Gloves,and D6319Standard Specification for Nitrile Examination Gloves forMedical Applications.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D412 Test Methods for Vulcanized Rubber and Thermoplas-tic ElastomersTensionD573 Test Method for RubberDeterioration in an AirOvenD3578 Specification for Rubber Examination GlovesD3767 Practice for RubberMeasurement of DimensionsD5151 Test Method for Detection of Holes in MedicalGlovesD6124 Test Method for Residual Powder on Medical GlovesD6319 Specification for Nitrile Examination Gloves forMedical ApplicationD6355 Test Method for Human Repeat Insult Patch Testingof Medical Gloves2.2 ISO Standard:ISO 2859 Sampling Procedures and Tables for Inspection byAttributes32.3 Other Document:U.S.Pharmacopeia43.Significance and Use3.1 This specification is intended as a referee procedure forevaluating the performance and safety of polychloroprenerubber examination gloves.It is not intended for testing prior toroutine lot release.The safe and proper use of polychloroprenerubber examination gloves is beyond the scope of this speci-fication.4.Material4.1 Any polychloroprene rubber compound that producesexamination gloves that meet the requirements of this specifi-cation are allowed.4.2 A lubricant that meets the current requirements of theU.S.Pharmacopoeia for absorbable dusting powder may beapplied to the glove.Other lubricants may be used if theirsafety and efficacy have been previously established.4.3 The inside and outside surface of the polychloroprenerubber examination gloves shall be free of talc.5.Performance Requirements5.1 Gloves,sampled in accordance with Section 6,shallmeet the following referee performance requirements:5.1.1 Products comply with requirements for sterility whentested in accordance with 7.2 when labeled sterile,5.1.2 Shall comply with freedom from holes when tested inaccordance with 7.3,5.1.3 Have consistent physical dimensions in accordancewith 7.4,5.1.4 Have acceptable physical property characteristics inaccordance with 7.5,1This specification is under the jurisdiction ofASTM Committee D11 on Rubberand Rubber-like Materials and is the direct responsibility of Subcommittee D11.40on Consumer Rubber Products.Current edition approved Nov.1,2019.Published December 2019.Originallyapproved in 2004.Last previous edition approved in 2016 as D6977 04(2016).DOI:10.1520/D6977-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036.4U.S.Pharmacopeia,latest edition,Mack Publishing Co.,Easton,PA 19175.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.1.5 Have a powder residue limit in accordance with 7.6,and5.1.6 Have a recommended maximum powder limit inaccordance with 7.7.6.Sampling6.1 For referee purposes,gloves shall be sampled fromfinished product,after sterilization when labeled sterile,andinspected in accordance with ISO 2859.The inspection levelsand acceptable quality levels(AQL)shall conform to thosespecified in Table 1,or as agreed upon between the purchaserand the seller,if the latter is more comprehensive.7.Referee Test Methods7.1 The following tests shal

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开