ASTM_D_6945_-_D_6945M_-_03_2017.pdf

Designation:D6945/D6945M03(Reapproved 2017)Standard Specification forEmulsified Refined Coal-Tar(Ready to Use,CommercialGrade)1This standard is issued under the fixed designation D6945/D6945M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers mineral-colloid-stabilized,emulsified refined coal tar suitable for use as a weather-protective and petroleum(aliphatic)solvent resistant coating.This product is typically applied to commercial lots and otherlow speed bituminous concrete pavements suitable for protec-tion.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C136/C136M Test Method for Sieve Analysis of Fine andCoarse AggregatesC142/C142M Test Method for Clay Lumps and FriableParticles in AggregatesD140/D140M Practice for Sampling Asphalt MaterialsD490 Specification for Road TarD2939 Test Methods for Emulsified Bitumens Used asProtective Coatings(Withdrawn 2012)3D3423/D3423M Practice for Application of EmulsifiedCoal-Tar Pitch(Mineral Colloid Type)D5727/D5727M Specification for Emulsified Refined CoalTar(Mineral Colloid Type)3.Terminology3.1 The refined coal tar emulsion mixed at the contractorsyard or at the job site shall meet the requirements of Specifi-cation D5727/D5727M.Mixture Types I and II(see AppendixA of Practice D3423/D3423M for standard definition of terms)are described below:3.1.1 Type I materiala mixture of refined coal tar emul-sion meeting Specification D5727/D5727M,water,and aggre-gate.3.1.2 Type II materiala mixture of refined coal tar emul-sion meeting Specification D5727/D5727M,water,aggregate,and additive.4.Classification4.1 This specification is designed to give specifying authori-ties the information necessary to ensure that the appropriatebase refined coal tar emulsion mixtures are specified forprotecting bituminous concrete pavements where fuel resis-tance is required.4.2 Normal aggregate loadings for Type I materials shouldrange from 0.360 to 0.600 kg/L3 to 5 lb/gal.Type II materialscan have slightly higher loadings of aggregate;however,aggregate loadings in excess of 0.720 kg/L 6 lb/gal arestrongly discouraged.NOTE1Several researchers have shown that high aggregate loadingsresult in a lack of fuel resistance as determined by the Resistance toKerosene test according to Test Methods D2939.Poor adhesion may alsooccur with high sand loadings.5.Materials and Manufacture5.1 Base Refined Coal Tar EmulsionThis emulsion shallbe made using binders prepared from a high temperature1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.09on Bituminous Emulsions.Current edition approved May 1,2017.Published May 2017.Originallyapproved in 2003.Last previous edition approved in 2011 as D6945/D6945M 03(2011)1.DOI:10.1520/D6945_D6945M-03R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 refined coal tar conforming to the requirements of SpecificationD490 for RT11 or higher.The use of oil and water gas tar is notallowed.The base refined coal tar emulsion shall be inaccordance with all requirements of Specification D5727/D5727M.5.2 AggregateThe aggregate shall be ei