ASTM_D_7241_-_22.pdf

Designation:D724122Standard Test Method forPile Thickness of Finished Multilevel Pile Yarn FloorCovering1This standard is issued under the fixed designation D7241;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of pilethickness of finished multilevel pile yarn floor covering usinga thickness measuring instrument having a stationary surface(platen),a circular pressure foot under specified force,andcapable of being moved vertically above the platen.1.2 This test method is applicable only to finished multilevelloop pile constructions.NOTE1Determination of pile thickness of multilevel pile yarn floorcoverings was previously contained within Test Method D418.For userconvenience,Subcommittee D13.21 subdivided Test Method D418 intoseparate standards of which this test method is one.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776 Practice for Conditioning and Testing TextilesD5684 Terminology Relating to Pile Floor CoveringsD5823 Test Method for Tuft Height of Pile Floor CoveringsE122 Practice for Calculating Sample Size to Estimate,WithSpecified Precision,the Average for a Characteristic of aLot or Process3.Terminology3.1 For definitions of terms relating to Pile Floor Coverings,refer to the Terminology D5684.3.2 The following terms are relevant to this standard:carpet,cut pile yarn floor covering,finished,finished pile yarn floorcovering,floor covering,pile,pile thickness,pile yarn floorcovering,pitch,primary backing,shorn pile stubble,stubbleheight,textile floor covering,tufted fabric.3.3 For definitions of other terms related to textiles,refer toTerminology D123.3.4 For discussion of terminology specific to this standard,see Annex A1.4.Summary of Test Method4.1 The thickness and mass are measured on each selectedstrip specimen in the unsheared condition and after removingapproximately 25,50,75%and all of the pile down to astubble by shearing.The net pile thicknesses at the 25,50,and75%levels are calculated by subtracting the stubble specimenthickness from the thicknesses measured at each of the otherstages.The net pile masses are calculated by subtracting themass of the stubble specimen from the four other weighings.The 25,50,and 75%net masses are expressed as a percent ofthe net pile mass of the unsheared specimen and the 25,50,and75%net thicknesses are plotted against these net masspercentages.Asmooth curve is drawn through the three plottedpoints.The net pile thickness corresponding to 50%net massis read from the smooth curve and doubled to obtain theaverage pile thickness.5.Significance and Use5.1 The determination of pile thickness of multilevel pileyarn floor covering is useful in quality and cost control duringmanufacture of pile yarn floor covering.The appearance andperformance may be affected by changes in pile thickness ofpile yarn floor coverings.This test method is considered1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.21 on Pile Floor Coverings.Current edition approved April 1,2022.Published May 2022.Originallyapproved in 2006.Last previous edition approved in 2013 as D7241-13 which waswithdrawn in January 2022 and reinstated in April 2022.DOI:10.1520/D7241-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical B