ASTM_D_8418_-_21.pdf

Designation:D841821Standard Guide forMaterial and Construction Standards Related toSustainability Within Committee D041This standard is issued under the fixed designation D8418;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide is intended to be a reference for locatingspecific test methods relating to materials and constructionstandards within the jurisdiction of Committee D04 on Roadand Paving Materials that could be a strategy used to meetproject sustainability goals.1.2 The guide needs to be reviewed and updated by Sub-committee D04.99 on Sustainable Asphalt Pavement Materialsand Construction,on an as-needed basis,to remain viable.1.2.1 Additions or deletions to the reference list in Section2 shall be submitted to Subcommittee D04.99 and balloted.1.3 UnitsThe values stated in SI units are to be regardedas standard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D8 Terminology Relating to Materials for Roads and Pave-mentsD692/D692M Specification for Coarse Aggregate for As-phalt Paving MixturesD1073 Specification for Fine Aggregate for Asphalt PavingMixturesD1752 Specification for Preformed Sponge Rubber,Corkand Recycled PVC Expansion Joint Fillers for ConcretePaving and Structural ConstructionD2940/D2940M Specification for Graded Aggregate Mate-rial for Bases or Subbases for Highways or AirportsD4215 Specification for Cold-Mixed,Cold-Laid AsphaltPaving MixturesD4552/D4552M Classification for Hot-Mix RecyclingAgentsD4792/D4792M Test Method for Potential Expansion ofAggregates from Hydration ReactionsD5106 Specification for Steel Slag Aggregates for Bitumi-nous Paving MixturesD6114/D6114M Specification for Asphalt-Rubber BinderD6155 Specification for Nontraditional Coarse Aggregatesfor Asphalt Paving MixturesD6932/D6932M Guide for Materials and Construction ofOpen-Graded Friction Course Plant Asphalt MixturesD7064/D7064M Practice for Open-Graded Friction Course(OGFC)Asphalt Mixture DesignD7564/D7564M Practice for Construction of Asphalt-Rubber Cape SealD7741/D7741M Test Method for Measurement of ApparentViscosity of Asphalt-Rubber or Other Asphalt Binders byUsing a Rotational Handheld ViscometerD8021 Guide for Blast Furnace and Steel Furnace Slag asProduced During the Manufacture of Iron and SteelD8055 Guide for Selecting an Appropriate Electronic Ther-mometer for Replacing Mercury Thermometers in D04Road and Paving StandardsD8125 Specification for Re-Refined Engine Oil Bottoms(REOB)/Vacuum Tower Asphalt Extender(VTAE)D8140 Guide for the Use of Foundry Sand in AsphaltMixturesD8378 Test Method for Potential Expansion of Steel Slagfrom Hydration Reactions by Autoclave3.Terminology3.1 DefinitionsFor the definitions of terms used in thisstandard refer to Terminology D8.1This guide is under the jurisdiction of ASTM Committee D04 on Road andPaving Materials and is the direct responsibility of Subcommittee D04.99 onSustainable Asphalt Pavement Materials and Construction.Current edition approved Nov.1,2021.Published November 2021.DOI:10.1520/D8418-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.14.Summary of Guide4.1 This guide is intended to be a reference for locatingspecific test methods relating to materials and constructionstandards within the jurisdiction of Committee D04 on Roadand Paving Materials that could be a strategy used to meetproject sustainability goals.4.2 These standards could include asphalt materials thatutilize recycled materials and industrial by-products,such asreclaimed asp