ASTM_D_8012_-_18.pdf

Designation:D801218Standard Practice forReclamation of Scrap and Waste Asphalt Shingles toProduce Reclaimed Asphalt Shingles(RAS)for Use inTransportation Applications1This standard is issued under the fixed designation D8012;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers reclamation of asphalt shinglesderived from manufacturing scrap and tear-off roofing.Re-claimed asphalt shingles(RAS)are used in roadway and otherapplications including asphalt paving materials and unboundmaterials such as granular fill.1.2 Guidance is provided relating to material quality,mate-rial quality control,and also operator and facility qualifica-tions.1.3 UnitsThe values stated in SI units are to be regardedas the standard.No other units of measurement are included inthis standard.NOTE1Sieve size is identified by its standard designation in Speci-fication E11.The alternative designation given in parentheses is forinformation only and does not represent a different standard sieve size.1.4 This practice offers a set of instructions for performingone or more specific operations.This document cannot replaceeducation or experience and should be used in conjunction withprofessional judgment.Not all aspects of this practice may beapplicable in all circumstances.This ASTM standard is notintended to represent or replace the standard of care by whichthe adequacy of a given professional service must be judged,nor should this document be applied without consideration ofa projects many unique aspects.The word“Standard”in thetitle means only that the document has been approved throughthe ASTM consensus process.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C136 Test Method for Sieve Analysis of Fine and CoarseAggregatesD75/D75M Practice for Sampling AggregatesD653 Terminology Relating to Soil,Rock,and ContainedFluidsD2216 Test Methods for Laboratory Determination of Water(Moisture)Content of Soil and Rock by MassE11 Specification for Woven Wire Test Sieve Cloth and TestSieves2.2 EPA Standard:3EPA 600-R-93-116 Polarized Light Microscopy:Method forthe Determination of Asbestos in Bulk Building Materials3.Terminology3.1 Definitions:3.1.1 For definitions of common technical terms in thisstandard,refer to Terminology D653.3.2 Definitions of Terms Specific to This Standard:3.2.1 asphalt shingle recycling facility(facility),nthephysical plant(or plants)where manufacturing scrap asphaltshingles and/or tear-off or other post-consumer asphalt shinglesare received,processed,tested,and stockpiled.This mayinclude separate transfer locations.3.2.2 asphalt shingle recycling operator(operator),nthecompany or companies that receive manufacturing scrap as-phalt shingles and/or tear-off or other post-consumer asphaltshingles and transform these materials into a finished RASproduct.1This test method is under the jurisdiction ofASTM Committee D18 on Soil andRock and is the direct responsibility of Subcommittee D18.14 on Geotechnics ofSustainable Construction.Current edition approved June 15,2018.Published July 2018.DOI:10.1520/D8012182For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3AvailablefromEnvironmentalProtectionAgency(EPA),https:/semspub.epa.gov/work/HQ/177098.pdf.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2.3 reclaimed asphalt shingles(RAS),nthe resultingproduct obtained from crushing,grinding,screening,andotherwise processing and recycling shingles derived frommanufacturing scrap(that is,manufacturing waste),tear-offroofing(that is,post-consumer materials),or other shinglemanufacturing waste and post-consumer asphalt shingles.3