温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_E_2245_
_11e1
Designation:E2245111Standard Test Method forResidual Strain Measurements of Thin,Reflecting FilmsUsing an Optical Interferometer1This standard is issued under the fixed designation E2245;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEReference(1)was editorially revised in September 2013.1.Scope1.1 This test method covers a procedure for measuring thecompressive residual strain in thin films.It applies only tofilms,such as found in microelectromechanical systems(MEMS)materials,which can be imaged using an opticalinterferometer,also called an interferometric microscope.Mea-surements from fixed-fixed beams that are touching the under-lying layer are not accepted.1.2 This test method uses a non-contact optical interfero-metric microscope with the capability of obtaining topographi-cal 3-D data sets.It is performed in the laboratory.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E2244 Test Method for In-Plane Length Measurements ofThin,Reflecting Films Using an Optical InterferometerE2246 Test Method for Strain Gradient Measurements ofThin,Reflecting Films Using an Optical InterferometerE2444 Terminology Relating to Measurements Taken onThin,Reflecting FilmsE2530 Practice for Calibrating the Z-Magnification of anAtomic Force Microscope at Subnanometer DisplacementLevels Using Si(111)Monatomic Steps(Withdrawn2015)32.2 SEMI Standard:4MS2 Test Method for Step Height Measurements of ThinFilms3.Terminology3.1 Definitions:3.1.1 The following terms can be found in TerminologyE2444.3.1.2 2-D data trace,na two-dimensional group of pointsthat is extracted from a topographical 3-D data set and that isparallel to the xz-or yz-plane of the interferometric micro-scope.3.1.3 3-D data set,na three-dimensional group of pointswith a topographical z-value for each(x,y)pixel locationwithin the interferometric microscopes field of view.3.1.4 anchor,nin a surface-micromachining process,theportion of the test structure where a structural layer is inten-tionally attached to its underlying layer.3.1.5 anchor lip,nin a surface-micromachining process,the freestanding extension of the structural layer of interestaround the edges of the anchor to its underlying layer.3.1.5.1 DiscussionIn some processes,the width of theanchor lip may be zero.3.1.6 bulk micromachining,adja MEMS fabrication pro-cess where the substrate is removed at specified locations.3.1.7 cantilever,na test structure that consists of a free-standing beam that is fixed at one end.3.1.8 fixed-fixed beam,na test structure that consists of afreestanding beam that is fixed at both ends.3.1.9 in-plane length(or deflection)measurement,ntheexperimental determination of the straight-line distance be-tween two transitional edges in a MEMS device.3.1.9.1 DiscussionThis length(or deflection)measure-ment is made parallel to the underlying layer(or the xy-planeof the interferometric microscope).1This test method is under the jurisdiction of ASTM Committee E08 on Fatigueand Fracture and is the direct responsibility of Subcommittee E08.05 on CyclicDeformation and Fatigue Crack Formation.Current edition approved Nov.1,2011.Published December 2011.Originallyapproved in 2002.Last previous edition approved in 2005 as E2245 05.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4For referenced Semiconductor Equipment and Materials International(SEMI)standards,visit the SEMI website,www.semi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.10 interferometer,na non-contact optical instrumentused to obtain topographical 3-D data sets.3.1.10.1 DiscussionThe height of the sample is measuredalong the z-axis of the interferometer.The x-axis is typicallyaligned parallel or perpendicular to the transitional edges to bemeasured.3.1.11 MEMS,adjmicroelectromechanical systems.3.1.12 microelectromechanical systems,adjin general,this term is used to describe micron-scale structures,sensors,actuators,and technologies used for their manufacture(such as,silicon process technologies),or combinations thereof.3.1.13 residual strain,nin a MEMS process,the amountof deformation(or displacement)per unit length constrainedwithin the structural layer of interest after fabric