ASTM_E_2252_-_18.pdf

Designation:E225218Standard Practice forSelection of Lead Hazard Reduction Methods for IdentifiedRisks in Residential Housing or Child Occupied Facilities1This standard is issued under the fixed designation E2252;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice describes the selection of lead hazardreduction methods for controlling lead hazard risks identifiedduring risk assessments of residential dwellings and childoccupied facilities.1.2 The values stated in SI units are to be regarded asstandard.The values given in parentheses are mathematicalconversions to inch-pound units that are provided for informa-tion only and are not considered standard.1.3 This practice contains notes,which are explanatory andare not part of the mandatory requirements of this standard.1.4 Method described in this practice may not meet or beallowed by requirements or regulations established by localauthorities having jurisdiction.It is the responsibility of theuser of this standard to comply with all such requirements andregulations.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2E917 Practice for Measuring Life-Cycle Costs of Buildingsand Building SystemsE1605 Terminology Relating to Lead in BuildingsE1795 Specification for Non-Reinforced Liquid Coating En-capsulation Products for Leaded Paint in BuildingsE1796 Guide for Selection and Use of Liquid CoatingEncapsulation Products for Leaded Paint in BuildingsE1797 Specification for Reinforced Liquid Coating Encap-sulation Products for Leaded Paint in BuildingsE2052 Guide for Evaluation,Management,and Control ofLead Hazards in Facilities(Withdrawn 2008)3E2115 Guide for Conducting Lead Hazard Assessments ofDwellings and of Other Child-Occupied FacilitiesE2239 Practice for Record Keeping and Record Preservationfor Lead Hazard Activities2.2 HUD Documents:4HUD Guidelines Guidelines for the Evaluation and Controlof Lead-Based Paint Hazards in Housing24 CFR Part 35 Requirements for Notification,Evaluationand Reduction of Lead-Based Paint Hazards in FederallyOwned Residential Property,and Housing Receiving Fed-eral Assistance;Final Rule,September 15,19992.3 EPA Documents:5Renovate Right:Important Lead Hazard Information forFamilies,Child Care Providers,and Schools40 CFR Part 745 Subpart L,Lead-Based Paint Activities2.4 NIBS Document:6NIBS Guidelines Lead-Based Paint:Operations and Main-tenance Work Practices Manual for Homes and Buildings2.5 RSMeans Document:7Building Construction Cost Data1This practice is under the jurisdiction of ASTM Committee E06 on Perfor-mance of Buildings and is the direct responsibility of Subcommittee E06.23 on LeadHazards Associated with Buildings.Current edition approved March 1,2018.Published April 2018.Originallyapproved in 2002.Last previous edition approved in 2012 as E2252 12.DOI:10.1520/E2252-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from U.S.Department of Housing and Urban Development(HUD),451 7th Street S.W.,Washington,DC 20410,http:/www.hud.gov.5Available from United States Environmental ProtectionAgency(EPA),WilliamJefferson Clinton Bldg.,Federal Triangle Complex,1200 Pennsylvania Ave.,NW,Washington,DC 20004,http:/www.epa.gov/lead.6Available from National Institute of Building Sciences(NIBS),1090 VermontAvenue,NW,Suite 700,Washington,DC 20005,http:/www.nibs.org.7Available from RSMeans data from Gordian,1099 Hingham St.,Ste.201,Rockland,MA 02370,http:/.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.Terminology3.1 DefinitionsFor defin