ASTM_E_1605_-_04_2012.pdf

Designation:E160504(Reapproved 2012)Standard Terminology Relating toLead in Buildings1This standard is issued under the fixed designation E1605;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This terminology standard covers definitions for thefollowing:1.1.1 Terms that are commonly used in the field of manage-ment of lead hazards in facilities;1.1.2 Architectural terms,particularly those associated witholder wood-frame buildings;and,1.1.3 Specialized terms that may be encountered by users inreports and notices that are generated during lead hazardmanagement activities.1.2 This terminology standard is supplementary to Termi-nology E631.1.3 Definitions adopted or derived from other documentsinclude the following:1.3.1 Some of the definitions in this terminology standardare adopted as exact copies from other sources.The source isbriefly identified at the right margin following the definitionand fully identified in Section 2.1.3.2 Some of the definitions in this terminology standardare adapted from other sources.Changes in these definitionswere made only to clarify the meaning,to incorporate relatedterms that also are defined in this terminology standard,or toensure that the revised definition is consistent with those forrelated terms.The source is briefly identified with the words“adapted”at the right margin following the definition,and isfully identified in Section 2.1.4 Terms within the definitions that are shown in boldfaceare defined in this terminology standard.1.5 This terminology standard excludes the following:1.5.1 Terms with a common dictionary meaning,except incases where there is a specialized definition within the field oflead hazard management.1.5.2 Terms that are used only in individual ASTM stan-dards in which they are defined adequately,whether formallyor by the context in which they appear.2.Referenced Documents2.1 ASTM Standards:2C186 Test Method for Heat of Hydration of HydraulicCementC859 Terminology Relating to Nuclear MaterialsD16 Terminology for Paint,Related Coatings,Materials,andApplicationsD123 Terminology Relating to TextilesD661 Test Method for Evaluating Degree of Cracking ofExterior PaintsD772 Test Method for Evaluating Degree of Flaking(Scal-ing)of Exterior PaintsD907 Terminology of AdhesivesD2864 Terminology Relating to Electrical Insulating Liq-uids and GasesD4214 Test Methods for Evaluating the Degree of Chalkingof Exterior Paint FilmsD4538 Terminology Relating to Protective Coating andLining Work for Power Generation FacilitiesE7 Terminology Relating to MetallographyE131 Terminology Relating to Molecular SpectroscopyE135 Terminology Relating to Analytical Chemistry forMetals,Ores,and Related MaterialsE344 Terminology Relating to Thermometry and Hydrom-etryE456 Terminology Relating to Quality and StatisticsE631 Terminology of Building ConstructionsE856 Definitions of Terms and Abbreviations Relating toPhysical and Chemical Characteristics of Refuse DerivedFuel(Withdrawn 2011)3E1187 Terminology Relating to Conformity Assessment(Withdrawn 2006)3E1227 Terminology for Chemical Analysis of Metals(With-drawn 1991)3E1553 Practice for Collection of Airborne Particulate LeadDuring Abatement and Construction Activities(With-drawn 2002)31This terminology is under the jurisdiction of ASTM Committee E06 onPerformance of Buildings and is the direct responsibility of Subcommittee E06.23on Lead Hazards Associated with Buildings.Current edition approved July 15,2012.Published August 2012.Originallyapproved in 1994.Last previous edition approved in 2004 as E1605 04.DOI:10.1520/E1605-04R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 E1613 Test Method for Determination of Lead by Induc-tively Coupled Plasma Atomic Emission Spectrometry(ICP-AES),Flame Atomic Absorption Spectrometry(FAAS),or Graphite Furnace Atomic Absorption Spec-trometry(GFAAS)TechniquesE1644 Practice for Hot Plate Digestion of Dust WipeSamples for the Determination of LeadE1728 Practice for Collection of Settled Dust Samples UsingWipe Sampling Methods for Subsequent Lead Determi-nationE1777 Guide for Prioritization of Data Needs for PavementManagementE1792 Specification for Wipe Sampling Materials for Leadin Surface DustE1796 Guide for Selection and Use of Liquid CoatingEncapsulation Products for Leaded Paint in BuildingsE1908 Guide for Sample Selection of Debris Waste from aBuilding Renovation or L