ASTM_E_2462_-_10.pdf

Designation:E246210Standard Performance Specification forCargo Bed Cover(CBC)HMMWV,Type I1This standard is issued under the fixed designation E2462;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 ScopeThis specification covers the performance re-quirements for the Type I Cargo Bed Cover(CBC).The Type ICargo Bed Cover is a removable general purpose rigid enclo-sure for the cargo bed of the M1152A1,M1152A1 with B2Armor Kit,M1037,M1042,M1097,and M1113 High-Mobility Multipurpose Wheeled Vehicle(HMMWV).TheType I CBC provides environmental protection and security formission equipment and items of general transport.1.2 The values stated in SI units are to be regarded asstandard.The values given in parentheses are mathematicalconversions to inch-pound units that are provided for informa-tion only and are not considered standard.1.3 The following safety hazards caveat pertains only to thetest required portion,Section 4,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2E1925 Specification for Engineering and Design Criteria forRigid Wall Relocatable Structures2.2 Army Standards:3ARMY TM 9-2320-280-10 HMMWVS Operators ManualARMY TM 10-5411-231-13&P Technical Manual2.3 Commercial Standards:ANSI/ASQC Z1.4-2003 Sampling Procedures and Tablesfor Inspection by Attributes4SAE AS8090 Mobility,TowedAerospaceGroundEquipment,General Requirements for52.4 Federal Standard:6FED-STD-595 Colors Used in Government Procurement2.5 Military Standards:6MIL-STD-129 Military Marking For Shipment and StorageMIL-STD-209 Interface Standard for Lifting and Tie-downProvisionsMIL-STD-810 Environmental Engineering Considerationsand Laboratory TestsMIL-STD-913 Requirements for the Certification of SlingLoaded Military Equipment for External Transportationby Department of Defense HelicoptersMIL-STD-1366 Transportability CriteriaMIL-PRF-22750 Coating,Epoxy,High SolidsMIL-C-46168 Coating,Aliphatic Polyurethane,ChemicalAgent ResistantMIL-C-53039 Coating,Aliphatic Polyurethane,SingleComponent,Chemical Agent ResistantMIL-DTL-53072 ChemicalAgentResistantCoating(CARC)SystemApplication Procedures and Quality Con-trol Inspection2.6 Military Handbook:6MIL-HDBK-1791 Designing for Internal Aerial Delivery inFixed Winged Aircraft2.7 The American Conference of Governmental IndustrialHygienists(ACGIH):7ACGIH Threshold Limit Values2.8 Drawings:381337-103984 Cargo Bed Cover,Type I(114Ton HM-MWV)1This specification is under the jurisdiction of ASTM Committee E06 onPerformance of Buildings and is the direct responsibility of Subcommittee E06.53on Materials and Processes for Durable Rigidwall Relocatable Structures.Current edition approved Nov.1,2010.Published December 2010.Originallyapproved in 2005.Last previous edition approved in 2005 as E2462 05.DOI:10.1520/E2462-102For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Shelter Technology,Engineering&Fabrication Directorate,US Army NatickSoldier RD&E Center,ATTN:RDNS-ST,Kansas Street,Natick,MA 01760-5018,http:/www.natick.army.mil.4Available from American Society for Quality(ASQ),600 N.Plankinton Ave.,Milwaukee,WI 53203,http:/www.asq.org.5Available from SAE International(SAE),400 Commonwealth Dr.,Warrendale,PA 15096-0001,http:/www.sae.org.6Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.7Available from American Conference of Governmental Industrial Hygienists,Inc.(ACGIH),1330 Kemper Meadow Dr.,Cincinnati,OH 45240,http:/www.acgih.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 81337-103984-101 Cargo Bed Cover,Type I(114TonHMMWV),Camouflage3.General Requirements3.1 Alternate Components and ConstructionThe interfacedrawings referenced herein specify the use of specific compo-nents and construction of previously produced CBCs.Specificmaterials,components and construction methods shall beconsidered for reference only.Dimensional characteristicsspecified in the interface drawings that are required for sparepart interchangeability and for operation and interoperability ofthe CBC with the vehicle shall be adhered to.When thisspecification or the referenced drawings specify use of aspecific component,the contractor may substitute a componentequal to the s