ASTM_E_1749_-_10.pdf

Designation:E174910Standard Terminology Relating toRigid Wall Relocatable Shelters1This standard is issued under the fixed designation E1749;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This terminology covers terms and their definitionsrelevant to the materials and processes associated with theconstruction of rigid wall relocatable shelters.2.Referenced Documents2.1 ASTM Standards:2B547/B547M Specification for Aluminum and Aluminum-Alloy Formed and Arc-Welded Round TubeC273 Test Method for Shear Properties of Sandwich CoreMaterialsC274 Terminology of Structural Sandwich ConstructionsC364 Test Method for Edgewise Compressive Strength ofSandwich ConstructionsC393 Test Method for Flexural Properties of SandwichConstructionsC460 Terminology forAsbestos-Cement(Withdrawn 2001)3C582 Specification for Contact-Molded Reinforced Thermo-setting Plastic(RTP)Laminates for Corrosion-ResistantEquipmentD123 Terminology Relating to TextilesD883 Terminology Relating to PlasticsD907 Terminology of AdhesivesD1079 Terminology Relating to Roofing and WaterproofingD1356 Terminology Relating to Sampling and Analysis ofAtmospheresD1566 Terminology Relating to RubberD1781 Test Method for Climbing Drum Peel for AdhesivesD2240 Test Method for Rubber PropertyDurometer Hard-nessD2730 Test Method for Sag Flow of Highly Viscous Mate-rials(Withdrawn 1986)3D3167 Test Method for Floating Roller Peel Resistance ofAdhesivesE492 Test Method for Laboratory Measurement of ImpactSound Transmission Through Floor-Ceiling AssembliesUsing the Tapping MachineE864 Practice for Surface Preparation of Aluminum Alloysto Be Adhesively Bonded in Honeycomb Shelter PanelsE874 Practice for Adhesive Bonding of Aluminum Facingsto Nonmetallic Honeycomb Core for Shelter PanelsE1925 Specification for Engineering and Design Criteria forRigid Wall Relocatable StructuresF412 Terminology Relating to Plastic Piping SystemsG15 Terminology Relating to Corrosion and Corrosion Test-ing(Withdrawn 2010)33.Terminologyabsolute sealinga level of sealing that requires all seams,slots,holes,and fasteners passing through the seal plane tobe sealed.accelerated testSee test,accelerated.adhesivea substance capable of holding materials togetherby means of surface attachment.D907cold setting adhesivean adhesive which sets at tempera-tures below 20C(68F).D907contact pressure adhesivea resinous adhesive which isaggressively and permanently tacky at room temperature andadheres to a variety of surfaces upon contact with a minimumof pressure required.(Syn.pressure-sensitive adhesives.)core splice adhesivea film adhesive,capable of expansionof at least 175%of its original thickness,used primarily to joinor splice together two or more separate sections of corematerial in sandwich constructions.foamed adhesive an adhesive,the apparent density ofwhich has been decreased substantially by the presence ofnumerous gaseous cells dispersed throughout its mass.D907supported film adhesivean adhesive material incorporatinga carrier that remains in the bond when the adhesive isemployed;carrier support material is usually composed oforganic/inorganic fibers which may be in woven(knit)ornonwoven(mat)form.1This terminology is under the jurisdiction of ASTM Committee E06 onPerformance of Buildings and is the direct responsibility of Subcommittee E06.53on Materials and Processes for Durable Rigidwall Relocatable Structures.Current edition approved Nov.1,2010.Published December 2010.Originallyapproved in 1995.Last previous edition approved in 2005 as E1749 05.DOI:10.1520/E1749-10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 unsupported film adhesivean adhesive material in filmform without a carrier support.adhesive,contactan adhesive that is apparently dry to thetouch and that will adhere to itself instantaneously uponcontact.alclad sheet and platecomposite sheet(and plate)having onboth surfaces a metallurgically bonded aluminum or alumi-num alloy coating that is anodic to the core alloy to which itis bonded,thus electrolytically protecting the core alloyagainst corrosion.B547/B547Mangle plyany filamentary lamina orientated in a directionother than that specified as 0(that is,the reference axis)within a composite assembly.anisotropicnot isotropic;having mechanical or physicalproperties,or both,that